[PATCH v9] PCI: Add device-specific reset for Qualcomm devices

[Alex Williamson]

On Fri, 12 Jun 2026 16:26:38 +0200
Jose Ignacio Tornos Martinez <jtornosm at redhat.com> wrote:

> Some Qualcomm PCIe devices (WCN6855/WCN7850 WiFi cards, SDX62/SDX65 modems)
> lack working reset methods for VFIO passthrough scenarios. These devices
> have no FLR capability, advertise NoSoftRst+ (blocking PM reset), and have
> broken bus reset.
> 
> The problem manifests in VFIO passthrough scenarios:
> 
> - WCN6855 WiFi card (17cb:1103): Normal VM operation works fine, including
>   clean shutdown/reboot. However, when the VM terminates uncleanly
>   (crash, force-off), VFIO attempts to reset the device before it can
>   be assigned to another VM. Without a working reset method, the device
>   remains in an undefined state, preventing reuse.
> 
> - WCN7850 WiFi card (17cb:1107): Same behavior as WCN6855.
> 
> - SDX62/SDX65 5G modems (17cb:0308): Never successfully initialize even
>   on first VM assignment without proper reset capability.
> 
> Add device-specific reset entries for these Qualcomm devices using D3hot
> power cycling. Testing shows that despite advertising NoSoftRst+, D3hot
> transition provides sufficient reset for VFIO reuse, particularly after
> unexpected VM termination. While not a complete reset (BARs preserved),
> it provides the only viable reset mechanism for these devices.
> 
> Testing was performed on desktop platforms with M.2 WiFi and modem cards
> using M.2-to-PCIe adapters, including extensive force-reset cycling to
> verify stability.
> 
> Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm at redhat.com>
> ---
> v9:
>   - Complete redesign based on maintainer feedback (Alex Williamson, Bjorn
>     Helgaas, Rafael Wysocki): dropped general d3cold infrastructure entirely
>     and now just a single patch: the proven D3hot reset for specific
>     Qualcomm devices (device-specific reset)
>   - Previous v8 patch 1/3 (general d3cold) dropped: concerns about ACPI
>     portability, bridge issues, runtime PM, and lack of _PR3 hardware for
>     testing.
>   - Previous v8 patch 3/3 (quirk_no_bus_reset) already merged for v7.2
> v8: https://lore.kernel.org/all/20260609163649.319755-1-jtornosm@redhat.com/
> 
>  drivers/pci/quirks.c | 38 ++++++++++++++++++++++++++++++++++++++
>  1 file changed, 38 insertions(+)
> 
> diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c
> index 431c021d7414..bac1edb6c2dc 100644
> --- a/drivers/pci/quirks.c
> +++ b/drivers/pci/quirks.c
> @@ -4240,6 +4240,41 @@ static int reset_hinic_vf_dev(struct pci_dev *pdev, bool probe)
>  	return 0;
>  }
>  
> +/*
> + * Device-specific reset method for certain Qualcomm devices via D3hot power
> + * cycle.
> + *
> + * These specific Qualcomm devices lack FLR capability, advertise NoSoftRst+
> + * (blocking PM reset), and have broken bus reset. Despite advertising
> + * NoSoftRst+, testing shows that D3hot transition provides sufficient reset
> + * for VFIO reuse, particularly after unexpected VM termination where the
> + * device would otherwise remain in an undefined state. While not a complete
> + * reset (BARs are preserved), it provides the only viable reset mechanism for
> + * these devices in the commented situations.
> + */
> +static int reset_qualcomm_d3hot(struct pci_dev *dev, bool probe)
> +{
> +	int ret;
> +
> +	if (probe)
> +		return 0;
> +
> +	if (dev->current_state != PCI_D0)
> +		return -EINVAL;
> +
> +	ret = pci_set_power_state(dev, PCI_D3hot);
> +	if (ret)
> +		return ret;
> +	msleep(200);
> +
> +	ret = pci_set_power_state(dev, PCI_D0);
> +	if (ret)
> +		return ret;
> +	msleep(200);
> +
> +	return 0;
> +}
> +
>  static const struct pci_dev_reset_methods pci_dev_reset_methods[] = {
>  	{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82599_SFP_VF,
>  		 reset_intel_82599_sfp_virtfn },
> @@ -4255,6 +4290,9 @@ static const struct pci_dev_reset_methods pci_dev_reset_methods[] = {
>  		reset_chelsio_generic_dev },
>  	{ PCI_VENDOR_ID_HUAWEI, PCI_DEVICE_ID_HINIC_VF,
>  		reset_hinic_vf_dev },
> +	{ PCI_VENDOR_ID_QCOM, 0x1103, reset_qualcomm_d3hot },  /* WCN6855 */
> +	{ PCI_VENDOR_ID_QCOM, 0x1107, reset_qualcomm_d3hot },  /* WCN7850 */
> +	{ PCI_VENDOR_ID_QCOM, 0x0308, reset_qualcomm_d3hot },  /* SDX62/SDX65 */
>  	{ 0 }
>  };
>  

Comment and scope is better, but this is duplicating the body of
pci_pm_reset() using a different mechanism with different timeouts. It
would be better to extract the core of pci_pm_reset() to a
pci_do_pm_reset() function that's used both here and by the
pci_pm_reset() function. Thanks,

Alex