[PATCH v2 1/2] wifi: ath12k: Remove frequency range filtering for single-phy devices

[Saikiran B]

Hi Baochen,

I checked the logs again.

The issue seems to be coming from how
[ath12k_regd_update()](drivers/net/wireless/ath/ath12k/reg.c) handles
frequency range updates for this device. WCN7850 is a single-phy
device (single [ar](drivers/net/wireless/ath/ath12k/mac.c) that
supports both 2.4GHz and 5GHz/6GHz.

In ath12k_regd_update():

1. It updates the range for 2GHz capabilities (sets range to ~2.4GHz).
2. It then attempts to update for 5GHz capabilities.
3. Because `ar->supports_6ghz` is true, it uses the 6GHz path logic.
4. However, `ab->reg_freq_6ghz` appears to be uninitialized/invalid at
this stage (possibly due to regulatory init timing or country code
issues, On Lenovo Yoga Slim 7x, SMBIOS does not seem to provide a
valid country code. The driver attempts to set an invalid country code
which the firmware rejects. This inturn triggers this issue. Fixing
SMBIOS parsing/defaults is a separate, complex issue that varies by
vendor.), causing the 5GHz range update to be skipped or invalid.

[ 11.699027] ath12k_pci 0004:01:00.0: Failed to set the requested
Country regulatory setting
[ 31.111995] ath12k_pci 0004:01:00.0: Failed to set the requested
Country regulatory setting

As a result, `ar->freq_range` remains effectively set for only the 2.4GHz band.

When ath12k_reg_update_chan_list() runs:

It compares 5GHz channels (e.g., 5180 MHz) against a
[freq_range](drivers/net/wireless/ath/ath12k/reg.c) that only covers
2.4GHz.
Result: `center_freq > end_freq` is TRUE -> Channel is filtered out.

The filtering logic added in acc152f9be20 works for split-phy topology
where each host ar covers a specific range. For WCN7850, where a
single host ar covers disjoint bands (2.4G + 5G), [freq_range] but
[freq_range](drivers/net/wireless/ath/ath12k/reg.c) (start/end) cannot
represent multiple disjoint bands at the same time.

Removing this driver-level filter allows the firmware (which knows the
true capabilities) to handle the channel list correctly.

Thanks & Regards,
Saikiran

On Tue, Jan 27, 2026 at 8:52 AM Baochen Qiang
<baochen.qiang at oss.qualcomm.com> wrote:
>
>
>
> On 1/26/2026 5:52 PM, Saikiran wrote:
> > The frequency range filtering added in commit acc152f9be20 was designed
> > for split-phy devices where multiple radios with overlapping frequency
> > ranges within the same band are combined into a single wiphy. Each radio
> > in such setups handles only a subset of channels within a band (e.g., two
> > 5GHz radios covering 5GHz-low and 5GHz-high separately).
> >
> > However, this filtering breaks single-phy devices like WCN7850 that use
> > a single radio to handle both 2.4GHz and 5GHz bands. On these devices,
>
> To be accurate, WCN7850 still gets two phys in hardware, it is just in host that we treat
> it as single.
>
> > the freq_range is set to cover the entire supported spectrum, but the
>
> exactly
>
> > filtering logic incorrectly restricts channels, causing 5GHz to become
> > completely unusable.
>
> how? what are the actual values of freq_range when you hit the issue and how are they
> calculated?
>
> >
> > The issue manifests as:
> > - All 5GHz channels filtered out during channel list updates
> > - No 5GHz SSIDs visible in scans
> > - Only 2.4GHz networks functional
> >
> > Remove the frequency range filtering entirely and rely on the firmware
> > to handle frequency restrictions based on actual hardware capabilities.
> > This approach works correctly for both split-phy and single-phy devices,
> > as the firmware has complete knowledge of what the hardware supports.
> >
> > Fixes: acc152f9be20 ("wifi: ath12k: combine channel list for split-phy devices in single-wiphy")
> > Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00302 (Lenovo Yoga Slim 7x)
> > Signed-off-by: Saikiran <bjsaikiran at gmail.com>
> > ---
> >  drivers/net/wireless/ath/ath12k/reg.c | 13 -------------
> >  1 file changed, 13 deletions(-)
> >
> > diff --git a/drivers/net/wireless/ath/ath12k/reg.c b/drivers/net/wireless/ath/ath12k/reg.c
> > index 7898f6981e5a..48c362a86524 100644
> > --- a/drivers/net/wireless/ath/ath12k/reg.c
> > +++ b/drivers/net/wireless/ath/ath12k/reg.c
> > @@ -153,12 +153,6 @@ int ath12k_reg_update_chan_list(struct ath12k *ar, bool wait)
> >                       if (bands[band]->channels[i].flags &
> >                           IEEE80211_CHAN_DISABLED)
> >                               continue;
> > -                     /* Skip Channels that are not in current radio's range */
> > -                     if (bands[band]->channels[i].center_freq <
> > -                         KHZ_TO_MHZ(ar->freq_range.start_freq) ||
> > -                         bands[band]->channels[i].center_freq >
> > -                         KHZ_TO_MHZ(ar->freq_range.end_freq))
> > -                             continue;
> >
> >                       num_channels++;
> >               }
> > @@ -190,13 +184,6 @@ int ath12k_reg_update_chan_list(struct ath12k *ar, bool wait)
> >                       if (channel->flags & IEEE80211_CHAN_DISABLED)
> >                               continue;
> >
> > -                     /* Skip Channels that are not in current radio's range */
> > -                     if (bands[band]->channels[i].center_freq <
> > -                         KHZ_TO_MHZ(ar->freq_range.start_freq) ||
> > -                         bands[band]->channels[i].center_freq >
> > -                         KHZ_TO_MHZ(ar->freq_range.end_freq))
> > -                             continue;
> > -
> >                       /* TODO: Set to true/false based on some condition? */
> >                       ch->allow_ht = true;
> >                       ch->allow_vht = true;
>