[PATCH ath-next v4 2/6] wifi: ath12k: Add ath12k_hw_params for IPQ5424

[Raj Kumar Bhagat]

On 03-04-2026 14:31, Baochen Qiang wrote:
>> +	{
>> +		.name = "ipq5424 hw1.0",
>> +		.hw_rev = ATH12K_HW_IPQ5424_HW10,
>> +		.fw = {
>> +			.dir = "IPQ5424/hw1.0",
>> +			.board_size = 256 * 1024,
>> +			.cal_offset = 128 * 1024,
>> +			.m3_loader = ath12k_m3_fw_loader_remoteproc,
>> +			.download_aux_ucode = false,
>> +		},
>> +		.max_radios = 1,
>> +		.single_pdev_only = false,
>> +		.qmi_service_ins_id = ATH12K_QMI_WLFW_SERVICE_INS_ID_V01_IPQ5332,
>> +		.internal_sleep_clock = false,
>> +
>> +		.hw_ops = &qcn9274_ops,
>> +		.ring_mask = &ath12k_wifi7_hw_ring_mask_ipq5332,
>> +
>> +		.host_ce_config = ath12k_wifi7_host_ce_config_ipq5332,
>> +		.ce_count = 12,
>> +		.target_ce_config = ath12k_wifi7_target_ce_config_wlan_ipq5332,
>> +		.target_ce_count = 12,
>> +		.svc_to_ce_map =
>> +			ath12k_wifi7_target_service_to_ce_map_wlan_ipq5332,
>> +		.svc_to_ce_map_len = 18,
>> +
>> +		.rxdma1_enable = true,
>> +		.num_rxdma_per_pdev = 1,
>> +		.num_rxdma_dst_ring = 0,
>> +		.rx_mac_buf_ring = false,
>> +		.vdev_start_delay = false,
>> +
>> +		.interface_modes = BIT(NL80211_IFTYPE_STATION) |
>> +				   BIT(NL80211_IFTYPE_AP) |
>> +				   BIT(NL80211_IFTYPE_MESH_POINT),
>> +		.supports_monitor = true,
>> +
>> +		.idle_ps = false,
>> +		.download_calib = true,
>> +		.supports_suspend = false,
>> +		.tcl_ring_retry = true,
>> +		.reoq_lut_support = false,
>> +		.supports_shadow_regs = false,
>> +
>> +		.num_tcl_banks = 48,
>> +		.max_tx_ring = 4,
>> +
>> +		.wmi_init = &ath12k_wifi7_wmi_init_qcn9274,
>> +
>> +		.qmi_cnss_feature_bitmap = BIT(CNSS_QDSS_CFG_MISS_V01),
>> +
>> +		.rfkill_pin = 0,
>> +		.rfkill_cfg = 0,
>> +		.rfkill_on_level = 0,
>> +
>> +		.rddm_size = 0,
>> +
>> +		.def_num_link = 0,
>> +		.max_mlo_peer = 256,
>> +
>> +		.otp_board_id_register = 0,
>> +
>> +		.supports_sta_ps = false,
>> +
>> +		.acpi_guid = NULL,
>> +		.supports_dynamic_smps_6ghz = false,
>> +		.iova_mask = 0,
>> +		.supports_aspm = false,
>> +
>> +		.ce_ie_addr = NULL,
>> +		.ce_remap = NULL,
>> +		.bdf_addr_offset = 0x940000,
>> +
>> +		.dp_primary_link_only = true,
>> +	},
>>   };
> mhi_config and current_cc_support are missing, please explicitly set them.

Sure will update in next version.