[PATCH ath-next] wifi: ath12k: allow beacon protection keys to be installed in hardware

[Karthikeyan Kathirvel]

On 4/29/2025 9:17 PM, Nicolas Escande wrote:
> On Mon Apr 21, 2025 at 1:47 PM CEST, Karthikeyan Kathirvel wrote:
>> Install beacon protection keys in hardware for AP modes only if hardware
>> supports it, as indicated by the WMI service bit
>> WMI_TLV_SERVICE_BEACON_PROTECTION_SUPPORT. Allow keyidx up to 7, since
>> beacon protection uses keyidx 6 and 7.
>>
>> Control this feature by setting bit 0 of feature_enable_bitmap when sending
>> the WMI_BCN_TMPL_CMDID command to firmware.
>>
>> Check for the beacon protection enabled bit in both tx and non-tx profiles
>> for MBSSID cases. If set in either profile, enable the beacon protection
>> feature in firmware for transmitted vif.
>>
>> Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
>>
>> Signed-off-by: Karthikeyan Kathirvel <karthikeyan.kathirvel at oss.qualcomm.com>
> [...]
>> @@ -4964,14 +4994,6 @@ static int ath12k_mac_op_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
>>   
>>   	lockdep_assert_wiphy(hw->wiphy);
>>   
>> -	/* BIP needs to be done in software */
>> -	if (key->cipher == WLAN_CIPHER_SUITE_AES_CMAC ||
>> -	    key->cipher == WLAN_CIPHER_SUITE_BIP_GMAC_128 ||
>> -	    key->cipher == WLAN_CIPHER_SUITE_BIP_GMAC_256 ||
>> -	    key->cipher == WLAN_CIPHER_SUITE_BIP_CMAC_256) {
>> -		return 1;
>> -	}
>> -
>>   	if (key->keyidx > WMI_MAX_KEY_INDEX)
>>   		return -ENOSPC;
>>   
> This hunk seems to break station mode on QCN9274. Maybe on WCN7850 too ? I see
> that it was not tested against that HW.
>
> With that hunk I cannot receive broadcast trafic sent by the ap anymore.
> Generated by a simple "arping -b X.X.X.X -I br0" in my case.
>
> Replacing that hunk with something similar as what is done in CLO [0] seems to
> fix the issue:
>
> @@ -5575,13 +5605,9 @@ static int ath12k_mac_op_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
>   
>   	lockdep_assert_wiphy(hw->wiphy);
>   
> -	/* BIP needs to be done in software */
> -	if (key->cipher == WLAN_CIPHER_SUITE_AES_CMAC ||
> -	    key->cipher == WLAN_CIPHER_SUITE_BIP_GMAC_128 ||
> -	    key->cipher == WLAN_CIPHER_SUITE_BIP_GMAC_256 ||
> -	    key->cipher == WLAN_CIPHER_SUITE_BIP_CMAC_256) {
> +	/* IGTK needs to be done in host software */
> +	if (key->keyidx == 4 || key->keyidx == 5)
>   		return 1;
> -	}
>   
>   	if (key->keyidx > WMI_MAX_KEY_INDEX)
>   		return -ENOSPC;
>
>
> PS: I tested that with firmware PCI WLAN.WBE.1.3.1-00218-QCAHKSWPL_SILICONZ-1
>
> [0] https://git.codelinaro.org/clo/qsdk/oss/system/feeds/wlan-open/-/blob/win.wlan_host_opensource.3.0/patches/ath12k/726-ath12k-add-beacon-protection-support-for-ath12k.patch?ref_type=heads

Thanks for catching this Nicolas, will check and get back on this