6GHz AP association failure on WCN7850

Wed Mar 6 06:49:03 PST 2024

Kang Yang <quic_kangyang at quicinc.com> 于2024年3月6日周三 14:45写道：
>
>
>
> On 3/6/2024 10:25 AM, Jun Nie wrote:
> > Kang Yang <quic_kangyang at quicinc.com> 于2024年3月5日周二 16:30写道：
> >>
> >>
> >>
> >> On 3/4/2024 6:14 PM, Jun Nie wrote:
> >>> Kang Yang <quic_kangyang at quicinc.com> 于2024年3月1日周五 19:42写道：
> >>>>
> >>>>
> >>>>
> >>>> On 3/1/2024 5:14 PM, Jun Nie wrote:
> >>>>> Hi,
> >>>>>
> >>>>> I see there is association failure many times when I try to connect my
> >>>>> 6GHz AP with latest mainline Linux. Does anyone also observe it too?
> >>>>> Any newer firmware than WLAN.HMT.2.0-01734 is available? Or we
> >>>>> recommend any specific version firmware?
> >>>>>
> >>>>> The issue only happens with this version firmware:
> >>>>>      [    9.441624] ath12k_pci 0000:01:00.0: Hardware name: wcn7850 hw2.0
> >>>>>       [   10.058822] ath12k_pci 0000:01:00.0: chip_id 0x2 chip_family 0x4
> >>>>> board_id 0x3d soc_id 0x40170200
> >>>>>       [   10.082876] ath12k_pci 0000:01:00.0: fw_version 0x200a06c6
> >>>>> fw_build_timestamp 2023-09-20 03:43 fw_build_id
> >>>>> QC_IMAGE_VERSION_STRING=WLAN.HMT.2.0-01734-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
> >>>>>
> >>>>
> >>>> Wrong firmware.
> >>>>
> >>>> We use WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 and
> >>>> WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4,
> >>>>
> >>>> https://github.com/kvalo/ath11k-firmware/tree/master/ath12k-testing/WCN7850/hw2.0
> >>>>
> >>>>> I do not see the issue with firmware:
> >>>>> [    7.896737] ath12k_pci 0000:01:00.0: fw_version 0x1005bc12
> >>>>> fw_build_timestamp 2022-10-11 12:13 fw_build_id
> >>>>> QC_IMAGE_VERSION_STRING=WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
> >>>>>
> >>>>
> >>>> That's it, i recommend you to use
> >>>> WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3. It's new one.
> >>>>
> >>>>
> >>>>
> >>>>> Detail log can be found at:
> >>>>> https://www.dropbox.com/scl/fi/jgn1zbnw44i1vypbjxl0v/ath12k-6GHz-association-fail-log.tgz?rlkey=pg2ifnzcttzimz7vaxb7tuc6w&dl=0
> >>>>>
> >>>>> Jun
> >>>
> >>> Hi Kang,
> >>>
> >>> I see wlan0 failure with below log with firmware version
> >>> WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4.
> >>
> >>
> >> Can you check if you completely replaces our upstream version?
> >>
> >> It is best not to mix it with other versions
> >> (board.bin/board.bin/regdb.bin/amss.bin/m3.bin).
> >>
> >> Mixed use may also have an impact on throughput.
> >>
> > Yeah, tried to replace all binaries from below path, but no help.
> > https://github.com/kvalo/ath11k-firmware/tree/master/ath12k-testing/WCN7850/hw2.0
> > https://github.com/kvalo/ath11k-firmware/tree/master/ath12k-testing/WCN7850/hw2.0/WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
> >
>
> So, both WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4. and
> WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 have this problem?
> Their log is the same?
>
>
>
>
> > What's your test platform? I use sm8650-hdk. Not sure whether there is something
> > platform dependent.
>
> Our test platform is x86 devices(normal x86 PC or x86 board).
>
> These binary can only be uploaded after detailed testing on x86 platform.
>
>
> > These binary was tested OK with Linux mainline on some QCOM platform, right?
> >
>
>
>
>
> Your platform is arm. Actually, we never test whether upstream firmware
> of ath12k can work well on other platforms. Any errors could happen.
>
>
>
> Did you download this firmware by git clone? Or just download manually.
>
> Please retry with git clone if you download manually.
>
>
>
You are right. It is downloading issue. binaries from git clone works well.
But 5GHz performance of version WLAN.HMT.1.0.c5-00481 is worse than
the 600Mbps on version WLAN.HMT.1.0-03427. The 6GHz performance
is similar, ~160Mbps. Do you what's the improvement of new firmware?

[  5]   0.00-1.00   sec  2.62 MBytes  22.0 Mbits/sec    0    144 KBytes
[  5]   1.00-2.00   sec  4.75 MBytes  39.8 Mbits/sec    0    335 KBytes
[  5]   2.00-3.00   sec  7.62 MBytes  64.1 Mbits/sec    0    622 KBytes
[  5]   3.00-4.00   sec  14.4 MBytes   121 Mbits/sec    0   1.15 MBytes
[  5]   4.00-5.00   sec  53.1 MBytes   446 Mbits/sec    0   2.35 MBytes
[  5]   5.00-6.00   sec  42.2 MBytes   354 Mbits/sec    0   2.91 MBytes
[  5]   6.00-7.00   sec  58.9 MBytes   494 Mbits/sec    0   2.91 MBytes
[  5]   7.00-8.00   sec  60.8 MBytes   510 Mbits/sec    0   2.91 MBytes
[  5]   8.00-9.00   sec  55.6 MBytes   466 Mbits/sec    0   2.91 MBytes
[  5]   9.00-10.00  sec  57.4 MBytes   480 Mbits/sec    0   2.91 MBytes

Thanks for your info!
- Jun
>
>
>
>
> >>
> >>
> >>
> >>
> >>> Do I need any patch outside mainline? Actually, I add below 2 patches
> >>> for 6GHz band.
> >>> afb7a22d9e22 wifi: ath12k: build 6 GHz regd based on vdev type and 6
> >>> GHz power type
> >>> 6c60469f0bae wifi: ath12k: add support to select 6 GHz Regulatory type
> >>>
> >>
> >>
> >> If problem still exist, please revert these patches and check again.
> >
> > Reverting them does not help as expected.
> >>
> >>
> >>
> >>
> >>>
> >>> [    6.194535] ath12k_pci 0000:01:00.0: setting mhi state: INIT(0)
> >>> [    6.195067] ath12k_pci 0000:01:00.0: setting mhi state: POWER_ON(2)
> >>> [    6.195069] mhi mhi0: Requested to power ON
> >>> [    6.195083] mhi mhi0: Power on setup success
> >>> [    6.196541] mhi mhi0: Image transfer failed
> >>> [    6.196559] mhi mhi0: Reg: ERROR_CODE value: 0xef128100
> >>> [    6.196574] mhi mhi0: Reg: ERROR_DBG1 value: 0xff7fc000
> >>> [    6.196588] mhi mhi0: Reg: ERROR_DBG2 value: 0x0
> >>> [    6.196601] mhi mhi0: Reg: ERROR_DBG3 value: 0x1988
> >>> [    6.196631] mhi mhi0: MHI did not load image over BHI, ret: -5
> >>>
> >>
> >> BTW, is it a probability problem?
> >
> > It happens 100%.
> >>
> >>> Kalle,
> >>> Thanks for the reminder of attachment size limitation!
> >>>
> >>> Jun