6GHz AP association failure on WCN7850

[Jun Nie]

Kang Yang <quic_kangyang at quicinc.com> 于2024年3月5日周二 16:30写道：
>
>
>
> On 3/4/2024 6:14 PM, Jun Nie wrote:
> > Kang Yang <quic_kangyang at quicinc.com> 于2024年3月1日周五 19:42写道：
> >>
> >>
> >>
> >> On 3/1/2024 5:14 PM, Jun Nie wrote:
> >>> Hi,
> >>>
> >>> I see there is association failure many times when I try to connect my
> >>> 6GHz AP with latest mainline Linux. Does anyone also observe it too?
> >>> Any newer firmware than WLAN.HMT.2.0-01734 is available? Or we
> >>> recommend any specific version firmware?
> >>>
> >>> The issue only happens with this version firmware:
> >>>     [    9.441624] ath12k_pci 0000:01:00.0: Hardware name: wcn7850 hw2.0
> >>>      [   10.058822] ath12k_pci 0000:01:00.0: chip_id 0x2 chip_family 0x4
> >>> board_id 0x3d soc_id 0x40170200
> >>>      [   10.082876] ath12k_pci 0000:01:00.0: fw_version 0x200a06c6
> >>> fw_build_timestamp 2023-09-20 03:43 fw_build_id
> >>> QC_IMAGE_VERSION_STRING=WLAN.HMT.2.0-01734-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
> >>>
> >>
> >> Wrong firmware.
> >>
> >> We use WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 and
> >> WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4,
> >>
> >> https://github.com/kvalo/ath11k-firmware/tree/master/ath12k-testing/WCN7850/hw2.0
> >>
> >>> I do not see the issue with firmware:
> >>> [    7.896737] ath12k_pci 0000:01:00.0: fw_version 0x1005bc12
> >>> fw_build_timestamp 2022-10-11 12:13 fw_build_id
> >>> QC_IMAGE_VERSION_STRING=WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
> >>>
> >>
> >> That's it, i recommend you to use
> >> WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3. It's new one.
> >>
> >>
> >>
> >>> Detail log can be found at:
> >>> https://www.dropbox.com/scl/fi/jgn1zbnw44i1vypbjxl0v/ath12k-6GHz-association-fail-log.tgz?rlkey=pg2ifnzcttzimz7vaxb7tuc6w&dl=0
> >>>
> >>> Jun
> >
> > Hi Kang,
> >
> > I see wlan0 failure with below log with firmware version
> > WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4.
>
>
> Can you check if you completely replaces our upstream version?
>
> It is best not to mix it with other versions
> (board.bin/board.bin/regdb.bin/amss.bin/m3.bin).
>
> Mixed use may also have an impact on throughput.
>
Yeah, tried to replace all binaries from below path, but no help.
https://github.com/kvalo/ath11k-firmware/tree/master/ath12k-testing/WCN7850/hw2.0
https://github.com/kvalo/ath11k-firmware/tree/master/ath12k-testing/WCN7850/hw2.0/WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3

What's your test platform? I use sm8650-hdk. Not sure whether there is something
platform dependent.
These binary was tested OK with Linux mainline on some QCOM platform, right?

>
>
>
>
> > Do I need any patch outside mainline? Actually, I add below 2 patches
> > for 6GHz band.
> > afb7a22d9e22 wifi: ath12k: build 6 GHz regd based on vdev type and 6
> > GHz power type
> > 6c60469f0bae wifi: ath12k: add support to select 6 GHz Regulatory type
> >
>
>
> If problem still exist, please revert these patches and check again.

Reverting them does not help as expected.
>
>
>
>
> >
> > [    6.194535] ath12k_pci 0000:01:00.0: setting mhi state: INIT(0)
> > [    6.195067] ath12k_pci 0000:01:00.0: setting mhi state: POWER_ON(2)
> > [    6.195069] mhi mhi0: Requested to power ON
> > [    6.195083] mhi mhi0: Power on setup success
> > [    6.196541] mhi mhi0: Image transfer failed
> > [    6.196559] mhi mhi0: Reg: ERROR_CODE value: 0xef128100
> > [    6.196574] mhi mhi0: Reg: ERROR_DBG1 value: 0xff7fc000
> > [    6.196588] mhi mhi0: Reg: ERROR_DBG2 value: 0x0
> > [    6.196601] mhi mhi0: Reg: ERROR_DBG3 value: 0x1988
> > [    6.196631] mhi mhi0: MHI did not load image over BHI, ret: -5
> >
>
> BTW, is it a probability problem?

It happens 100%.
>
> > Kalle,
> > Thanks for the reminder of attachment size limitation!
> >
> > Jun