[PATCH v4 2/2] wifi: ath12k: Support pdev Puncture Stats

[Kalle Valo]

Roopni Devanathan <quic_rdevanat at quicinc.com> writes:

> From: Rajat Soni <quic_rajson at quicinc.com>
>
> Add support to request pdev puncture stats from firmware through
> HTT stats type 46. These stats give the count of number of
> subbands used in different wifi standards.
>
> Sample output:
> -------------
> echo 46 > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats_type
> cat /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats
> HTT_PDEV_PUNCTURE_STATS_TLV:
> mac_id = 0
> tx_ofdm_su_last_used_pattern_mask = 0x00000001
> tx_ofdm_su_num_subbands_used_cnt_01 = 217
> tx_ofdm_su_num_subbands_used_cnt_02 = 0
> tx_ofdm_su_num_subbands_used_cnt_03 = 0
> .....
>
> HTT_PDEV_PUNCTURE_STATS_TLV:
> mac_id = 0
> tx_ax_dl_mu_ofdma_last_used_pattern_mask = 0x00000000
> tx_ax_dl_mu_ofdma_num_subbands_used_cnt_01 = 0
> tx_ax_dl_mu_ofdma_num_subbands_used_cnt_02 = 0
> tx_ax_dl_mu_ofdma_num_subbands_used_cnt_03 = 0
> .....
>
> HTT_PDEV_PUNCTURE_STATS_TLV:
> mac_id = 0
> tx_be_dl_mu_ofdma_last_used_pattern_mask = 0x00000000
> tx_be_dl_mu_ofdma_num_subbands_used_cnt_01 = 0
> tx_be_dl_mu_ofdma_num_subbands_used_cnt_02 = 0
> tx_be_dl_mu_ofdma_num_subbands_used_cnt_03 = 0
> .....
>
> HTT_PDEV_PUNCTURE_STATS_TLV:
> mac_id = 0
> rx_ax_ul_mu_ofdma_last_used_pattern_mask = 0x00000000
> rx_ax_ul_mu_ofdma_num_subbands_used_cnt_01 = 0
> rx_ax_ul_mu_ofdma_num_subbands_used_cnt_02 = 0
> rx_ax_ul_mu_ofdma_num_subbands_used_cnt_03 = 0
> .....
>
> HTT_PDEV_PUNCTURE_STATS_TLV:
> mac_id = 0
> rx_be_ul_mu_ofdma_last_used_pattern_mask = 0x00000000
> rx_be_ul_mu_ofdma_num_subbands_used_cnt_01 = 0
> rx_be_ul_mu_ofdma_num_subbands_used_cnt_02 = 0
> rx_be_ul_mu_ofdma_num_subbands_used_cnt_03 = 0
> .....
>
> Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
> Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
>
> Signed-off-by: Rajat Soni <quic_rajson at quicinc.com>
> Signed-off-by: Roopni Devanathan <quic_rdevanat at quicinc.com>

[...]

> +static const char*
> +ath12k_htt_get_punct_ppdu_type_str(enum ath12k_htt_stats_ppdu_type ppdu_type,
> +				   struct debug_htt_stats_req *stats_req)
> +{
> +	const char *ppdu_type_str = "unknown";
> +	u32 len = stats_req->buf_len;
> +
> +	switch (ppdu_type) {
> +	case ATH12K_HTT_STATS_PPDU_TYPE_MODE_SU:
> +		ppdu_type_str = "su";
> +		break;
> +	case ATH12K_HTT_STATS_PPDU_TYPE_DL_MU_MIMO:
> +		ppdu_type_str = "dl_mu_mimo";
> +		break;
> +	case ATH12K_HTT_STATS_PPDU_TYPE_UL_MU_MIMO:
> +		ppdu_type_str = "ul_mu_mimo";
> +		break;
> +	case ATH12K_HTT_STATS_PPDU_TYPE_DL_MU_OFDMA:
> +		ppdu_type_str = "dl_mu_ofdma";
> +		break;
> +	case ATH12K_HTT_STATS_PPDU_TYPE_UL_MU_OFDMA:
> +		ppdu_type_str = "ul_mu_ofdma";
> +		break;
> +	default:
> +		break;
> +	}
> +
> +	stats_req->buf_len = len;
> +	return ppdu_type_str;
> +}

Also here I don't get why the len variable is needed. I would just
simplify this and the previous function to:

static const char*
ath12k_htt_get_punct_ppdu_type_str(enum ath12k_htt_stats_ppdu_type ppdu_type,
				   struct debug_htt_stats_req *stats_req)
{
	switch (ppdu_type) {
	case ATH12K_HTT_STATS_PPDU_TYPE_MODE_SU:
		return "su";
	case ATH12K_HTT_STATS_PPDU_TYPE_DL_MU_MIMO:
		return "dl_mu_mimo";
	case ATH12K_HTT_STATS_PPDU_TYPE_UL_MU_MIMO:
		return "ul_mu_mimo";
	case ATH12K_HTT_STATS_PPDU_TYPE_DL_MU_OFDMA:
		return "dl_mu_ofdma";
	case ATH12K_HTT_STATS_PPDU_TYPE_UL_MU_OFDMA:
		return "ul_mu_ofdma";
	default:
		return "unknown";
	}

-- 
https://patchwork.kernel.org/project/linux-wireless/list/

https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches