[PATCH v2 02/19] ath11k: Refactor PCI code to support hybrid bus devices

[Kalle Valo]

Manikanta Pubbisetty <quic_mpubbise at quicinc.com> writes:

> Unlike other ATH11K PCIe devices which are enumerated by APSS
> processor (Application Processor SubSystem), WCN6750 gets
> enumerated by the WPSS Q6 processor (Wireless Processor SubSystem);
> In simple terms, though WCN6750 is PCIe device, it is not attached
> to the APSS processor, APSS will not know of such a device being
> present in the system and therefore WCN6750 will be registered as
> a platform device to the kernel core like other supported AHB
> devices.
>
> WCN6750 uses both AHB and PCI APIs for it's operation, it uses
> AHB APIs for device probe/boot and PCI APIs for device setup
> and register accesses; Because of this nature, it is referred
> as a hybrid bus device.
>
> Refactor PCI code to support hybrid bus devices like WCN6750.
>
> Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
> Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
> Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
> Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
>
> Signed-off-by: Manikanta Pubbisetty <quic_mpubbise at quicinc.com>

[...]

> --- a/drivers/net/wireless/ath/ath11k/Makefile
> +++ b/drivers/net/wireless/ath/ath11k/Makefile
> @@ -29,7 +29,7 @@ obj-$(CONFIG_ATH11K_AHB) += ath11k_ahb.o
>  ath11k_ahb-y += ahb.o
>  
>  obj-$(CONFIG_ATH11K_PCI) += ath11k_pci.o
> -ath11k_pci-y += mhi.o pci.o
> +ath11k_pci-y += mhi.o pci.o pci_cmn.o

So the end result looks like this:

obj-$(CONFIG_ATH11K_AHB) += ath11k_ahb.o
ath11k_ahb-y += ahb.o pci_cmn.o

obj-$(CONFIG_ATH11K_PCI) += ath11k_pci.o
ath11k_pci-y += mhi.o pci.o pci_cmn.o

Linking pci_cmn.o to both ath11k_pci.ko and ath11k_ahb.ko looks wrong.
Does that even compile if ath11k is linked to the kernel, eg. with
allyesconfig?

One way to solve is to link pci_cmn.o to ath11k.ko. But for another
approach, for a long time I have been thinking about what's the point to
have separate ath11k_pci.ko and ath11k_ahb.ko modules?,They are very
small anyway compared to ath11k.ko. So my ideais that should we have
just one ath11k.ko module, it contains all AHB and PCI code as well, and
ath11k_pci.ko and ath11k_ahb.ko would not be created anymore. It would
simplify things a bit, especially here.

Thoughts?

-- 
https://patchwork.kernel.org/project/linux-wireless/list/

https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches