[PATCH v2 00/19] add support for WCN6750

Manikanta Pubbisetty quic_mpubbise at quicinc.com
Sun Feb 20 22:29:33 PST 2022


On 1/28/2022 3:37 PM, Kalle Valo wrote:

> Manikanta Pubbisetty <quic_mpubbise at quicinc.com> writes:
>
>> WCN6750 is non-DBS 2x2 11AX chipset. Unlike QCA6390/WCN6855 which
>> are DBS (dual band simultaneous) solutions (2 LMACs), WCN6750 has a
>> single LMAC supporting 2G, 5G and 6G bands. It can be operated only
>> on one band at any given point.
>>
>> WCN6750 is a PCIe device. Unlike other supported ATH11K PCIe devices
>> which are directly attached to APSS (Application Processor SubSystem),
>> WCN6750 is not attached to APSS, it is attached to the WPSS
>> (Wireless Processor SubSystem) Q6 processor, the FW which runs on the
>> Q6 processor will enumerate the PCIe device. Since APSS is unaware of
>> such a device, it has to be registered as a platform device(AHB) to the
>> kernel for device probing. Like other AHB devices, remoteproc APIs are
>> used to boot up or shutdown of WCN6750.
>>
>> WCN6750 uses both AHB and PCIe ATH11K APIs for it's operation.
>> It uses AHB APIs for device probe and booting of the remote processor.
>> Once device is booted up, it uses ATH11K PCIe APIs for initialization
>> and register access. Hence, it is referred as hybrid bus device in
>> the rest of this series.
>>
>> Since the chip is enumerated by WPSS Q6, device information like
>> BAR and BAR size is not known to the APSS processor. A new QMI message
>> called device info QMI request will be sent to the target for fetching
>> these details.
>>
>> STA and AP modes are supported; Basic connectivity and ping are
>> verified in both the modes.
>>
>> Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
>> Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
>> Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
>> Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
>>
>> Note:
>> *	Remoteproc driver changes for WCN6750 which takes care of
>> 	downloading the FW and booting of Q6 processor are under
>> 	upstream review.
>> 	Link: https://patchwork.kernel.org/project/linux-remoteproc/list/?series=582475
> This is a very good overview, thanks for that. But I think something
> which is not clearly mentioned here is that this only works on Qualcomm
> Snapdragon SoC, right?

You are absolutely right.

>   So even though WCN6750 is a PCI device, it cannot
> be attached to any platform. It would be good to emphasise that.

I'll add this detail in the next revision.

>> Manikanta Pubbisetty (19):
>>    ath11k: PCI changes to support WCN6750
>>    ath11k: Refactor PCI code to support hybrid bus devices
>>    ath11k: Choose MSI config based on HW revision
>>    ath11k: Refactor MSI logic
>>    ath11k: Remove core PCI references from PCI common code
>>    ath11k: Add HW params for WCN6750
>>    ath11k: Add bus params for WCN6750
>>    ath11k: Add register access logic for WCN6750
>>    ath11k: Fetch device information via QMI for WCN6750
>>    ath11k: Add QMI changes for WCN6750
>>    ath11k: HAL changes to support WCN6750
>>    ath11k: Datapath changes to support WCN6750
>>    ath11k: Fix RX de-fragmentation issue on WCN6750
>>    ath11k: Do not put HW in DBS mode for WCN6750
>>    ath11k: WMI changes to support WCN6750
>>    ath11k: Update WBM idle ring HP after FW mode on
>>    ath11k: Add support for WCN6750 device
>>    ath11k: Add support for targets without trustzone
>>    dt: bindings: net: add bindings of WCN6750 for ath11k
> 19 patches is a lot to chew on in one go, my recommendation is to have
> max 10-12 patches per set.
>
> In this case having three patchsets would make it a lot easier for
> reviewers, but not sure how to split them. Maybe you could submit these
> patches separate for preparing WCN6750 support, after a quick look they
> seem pretty independent:
>
>    ath11k: Fetch device information via QMI for WCN6750
>    ath11k: HAL changes to support WCN6750
>    ath11k: Fix RX de-fragmentation issue on WCN6750
>    ath11k: Do not put HW in DBS mode for WCN6750
>    ath11k: WMI changes to support WCN6750
Sure, I'll logically split the series in the next revisions.



More information about the ath11k mailing list