[PATCH v2 8/8] arm64: dts: qcom: arduino-imola: Describe NVMEM layout for WiFi/BT addresses

[Loic Poulain]

On Arduino Uno-Q, the eMMC boot1 partition is factory provisioned
with device-specific information such as the WiFi MAC address
and the Bluetooth BD address. This partition can serve as an
alternative to additional non-volatile memory, such as a
dedicated EEPROM.

The eMMC boot partitions are typically good candidates, as they
are relatively small, read-only by default (and can be enforced
as hardware read-only), and are not affected by board reflashing
procedures, which generally target the eMMC user or GP partitions.

Describe the corresponding nvmem-layout for the WiFi and Bluetooth
addresses, and point the WiFi and Bluetooth nodes to the appropriate
NVMEM cells to retrieve them.

Signed-off-by: Loic Poulain <loic.poulain at oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio at oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/qrb2210-arduino-imola.dts | 34 ++++++++++++++++++++++
 1 file changed, 34 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qrb2210-arduino-imola.dts b/arch/arm64/boot/dts/qcom/qrb2210-arduino-imola.dts
index bf088fa9807f040f0c8f405f9111b01790b09377..6ed91cccae2fbf0723629a4db12d2724312d50b2 100644
--- a/arch/arm64/boot/dts/qcom/qrb2210-arduino-imola.dts
+++ b/arch/arm64/boot/dts/qcom/qrb2210-arduino-imola.dts
@@ -409,7 +409,35 @@ &sdhc_1 {
 	no-sdio;
 	no-sd;
 
+	#address-cells = <1>;
+	#size-cells = <0>;
+
 	status = "okay";
+
+	card at 0 {
+		compatible = "mmc-card";
+		reg = <0>;
+
+		partitions-boot1 {
+			nvmem-layout {
+				compatible = "fixed-layout";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				wifi_mac_addr: mac-addr at 4400 {
+					compatible = "mac-base";
+					reg = <0x4400 0x6>;
+					#nvmem-cell-cells = <1>;
+				};
+
+				bd_addr: bd-addr at 5400 {
+					compatible = "mac-base";
+					reg = <0x5400 0x6>;
+					#nvmem-cell-cells = <1>;
+				};
+			};
+		};
+	};
 };
 
 &spi5 {
@@ -512,6 +540,9 @@ bluetooth {
 		vddch0-supply = <&pm4125_l22>;
 		enable-gpios = <&tlmm 87 GPIO_ACTIVE_HIGH>;
 		max-speed = <3000000>;
+
+		nvmem-cells = <&bd_addr 0>;
+		nvmem-cell-names = "local-bd-address";
 	};
 };
 
@@ -557,6 +588,9 @@ &wifi {
 	qcom,ath10k-calibration-variant = "ArduinoImola";
 	firmware-name = "qcm2290";
 
+	nvmem-cells = <&wifi_mac_addr 0>;
+	nvmem-cell-names = "mac-address";
+
 	status = "okay";
 };
 

-- 
2.34.1