QCA9880 slow performance adhoc/IBSS mode
Ben Greear
greearb at candelatech.com
Tue Feb 28 14:02:39 PST 2017
I've pushed 475+Mbps on apu2 over wifi, maybe more. That was AP mode, most likely.
IBSS on ath10k cannot do AMSDU, so you loose a bit of performance there,
but otherwise it should be pretty similar to AP/STA mode. To verify, try
running in AP/STA mode.
Thanks,
Ben
On 02/28/2017 01:48 PM, Ralph Houthoofdt wrote:
> Dear Ben,
>
> The speeds I'm reporting are UDP using these commands for the client:
> Iperf3 -uVc <serverAddress> -b0 -w128k
> Iperf3 -uRVc <serverAddress> -b0 -w128k
>
> I will try relocating the nodes and try different antenna positions and
> angles.
> As you see it, this problem is purely because of the environment, not
> because of the configuration or drivers?
>
> I will let you know what the results of relocation are tomorrow. Thanks for
> your help!
>
> Kind regards,
> Met vriendelijke groeten,
> Ralph Houthoofdt
> Student master industriële wetenschappen: informatica
>
> -----Original Message-----
> From: Ben Greear [mailto:greearb at candelatech.com]
> Sent: dinsdag 28 februari 2017 19:12
> To: Ralph Houthoofdt <ralph.houthoofdt at ugent.be>
> Cc: ath10k at lists.infradead.org
> Subject: Re: QCA9880 slow performance adhoc/IBSS mode
>
> You try UDP yet, or is this all TCP?
>
> Also, with some better antenna positions and/or better other RF environment,
> you should see NSS of 3, hopefully MCS of 6 or higher.
>
> On 02/28/2017 10:02 AM, Ralph Houthoofdt wrote:
>> Dear Ben,
>>
>> I ran the same test again, this time running the iperf3 server on my
>> laptop and the client on the node. I could indeed see CPU usage rise
>> to 40% on my laptop, the node stayed at roughly 10%. The speeds
>> remained roughly the same. 215Mbit one way, 40Mbit the other.
>>
>> As for the tx/rx rates I get these values:
>> tx bitrate: 234.0 MBit/s VHT-MCS 3 80MHz VHT-NSS 2
>> rx bitrate: 87.8 MBit/s VHT-MCS 2 80MHz VHT-NSS 1
>>
>> I set the 4 antennas facing different directions approximately at 135
>> degree angles relative to the device.
>
> You try UDP yet, or is this all TCP?
>
> Also, with some better antenna positions and/or better other RF environment,
> you should see NSS of 3, hopefully MCS of 6 or higher.
>
> The 9880 has 3 antenna, so how did you get to 4?
>
> Thanks,
> Ben
>
>>
>> Thank you for your help so far. I will be leaving home for a few hours
>> and will be responding to any replies tomorrow morning.
>>
>> Met vriendelijke groeten,
>> Ralph Houthoofdt
>> Student industriële wetenschappen informatica
>>
>> -----Original Message-----
>> From: Ben Greear [mailto:greearb at candelatech.com]
>> Sent: dinsdag 28 februari 2017 18:42
>> To: Ralph Houthoofdt <ralph.houthoofdt at ugent.be>
>> Cc: ath10k at lists.infradead.org
>> Subject: Re: QCA9880 slow performance adhoc/IBSS mode
>>
>> Try UDP to make sure you are not hitting a TCP issue.
>>
>> Try running iperf server on another laptop so that CPU of your nodes
>> is less important.
>>
>> Check the tx/rx encoding rates to make sure you are getting good RF
>> behaviour. 'iw ... station dump'
>>
>> Ensure antennas are not pointing all in the same direction so that you
>> can get some diversity working.
>>
>> Thanks,
>> Ben
>>
>> On 02/28/2017 09:36 AM, Ralph Houthoofdt wrote:
>>> Dear Ben,
>>>
>>> Thank you for your quick reply.
>>>
>>> My mesh is running on channel 36 using VHT80 and a TX power of 20
>>> dbm, the maximum allowed according to my regulatory settings from iw
>>> reg get. The hwmode is set as 11a.
>>> I have also enable the following ht_capabilities on my radio in
>>> /etc/config/wireless:
>>>
>>> list ht_capab 'short_gi_80'
>>> list ht_capab 'max-mpdu-11454'
>>> list ht_capab 'TX-STBC-2BY1'
>>> list ht_capab 'RX-STBC1'
>>> list ht_capab 'RX-ANTENNA-PATTERN'
>>> list ht_capab 'TX-ANTENNA-PATTERN'
>>> list ht_capab 'MAX-A-MPDU-LEN-EXP7'
>>>
>>> I just finished running iperf3 from my laptop (2nd gen Core i7) to
>>> one of my nodes. The results were indeed a bit different.
>>> Iperf server was running on my node and my laptop was the client.
>>> UDP:
>>> Normal: average result of 221Mbit, which is pretty normal I think.
>>> Reverse: average result of 41Mbit, which is better than the average
>>> 20Mbit I got when running iperf3 using 2 nodes.
>>> TCP:
>>> Normal: average result of 49Mbit
>>> Reverse: average result of 35.4Mbit
>>>
>>> In terms of congestion, I'm not sure what you mean, but I'm in a low
>>> populated area with few wireless access points. I disabled all my
>>> 5GHz devices except for the mesh nodes. InSSIDer only shows my nodes
>>> in the 5GHz range.
>>>
>>> Is there anything else I could try for you?
>>>
>>> Met vriendelijke groeten,
>>> Ralph Houthoofdt
>>> Student industriële wetenschappen informatica
>>>
>>> -----Original Message-----
>>> From: ath10k [mailto:ath10k-bounces at lists.infradead.org] On Behalf Of
>>> Ben Greear
>>> Sent: dinsdag 28 februari 2017 17:56
>>> To: Ralph Houthoofdt <ralph at rora.be>; ath10k at lists.infradead.org
>>> Subject: Re: QCA9880 slow performance adhoc/IBSS mode
>>>
>>> Run iperf on a separate machine, as the apu2 have too weak of a CPU
>>> to drive the wifi network at full speed. And, publish what results
>>> you do get, including RF information such as channel and how
>>> congested is your test area. Try udp as well as tcp.
>>>
>>> Thanks,
>>> Ben
>>>
>>> On 02/28/2017 08:51 AM, Ralph Houthoofdt wrote:
>>>> Dear all,
>>>>
>>>> I’m currently doing me masters thesis on the subject of Wireless
>>>> Mesh Networks and how to optimize them for home use.
>>>> The devices I use are 5x PC Engine APU2c4 with 2x QCA9880 chip
>>>> (Compex WLE900VX). All of them are running LEDE (OpenWRT fork).
>>>>
>>>> The problem I’m experiencing is the same as
>>>> http://lists.infradead.org/pipermail/ath10k/2017-January/009075.html .
>>>> Using the tips mentioned I did not come to a better performance. I’m
>>>> thinking it’s driver related..
>>>> When running iperf3 only one direction is running at a reasonable
>>>> throughput. Since I am using adhoc mode primarily I decided to use
>>>> these
>>>> packages:
>>>> - Kmod-ath10k-ct
>>>> - Ath10k-firmware-qca988x-ct
>>>> Some sources on the internet said that using the Candela Tech
>>>> drivers should result in better support for adhoc/mesh networks.
>>>>
>>>> As suggested in the other issue linked above, I switched TCP
>>>> congestion control to ‘Reno’ instead of the default ‘Cubic’.
>>>> I also did try the command “iw reg set BE” since I am from Belgium,
>>>> but running “iw reg get” right after still gave me US as a result.
>>>>
>>>> Let me know what additional command info I should post. Any help
>>>> would be greatly appreciated.
>>>>
>>>> Iwconfig:
>>>> adhoc0 IEEE 802.11 ESSID:"mesh"
>>>> Mode:Ad-Hoc Frequency:5.18 GHz Cell: 02:CA:FE:CA:CA:40
>>>> Tx-Power=20 dBm
>>>> RTS thr:off Fragment thr:off
>>>> Encryption key:off
>>>> Power Management:off
>>>>
>>>>
>>>> Iw reg get (I’m from Belgium):
>>>> global
>>>> country BE: DFS-ETSI
>>>> (2402 - 2482 @ 40), (N/A, 20), (N/A)
>>>> (5170 - 5250 @ 80), (N/A, 20), (N/A), AUTO-BW
>>>> (5250 - 5330 @ 80), (N/A, 20), (0 ms), DFS, AUTO-BW
>>>> (5490 - 5710 @ 160), (N/A, 27), (0 ms), DFS
>>>> (57000 - 66000 @ 2160), (N/A, 40), (N/A)
>>>>
>>>> phy#1
>>>> country US: DFS-FCC
>>>> (2402 - 2472 @ 40), (N/A, 30), (N/A)
>>>> (5170 - 5250 @ 80), (N/A, 23), (N/A), AUTO-BW
>>>> (5250 - 5330 @ 80), (N/A, 23), (0 ms), DFS, AUTO-BW
>>>> (5490 - 5730 @ 160), (N/A, 23), (0 ms), DFS
>>>> (5735 - 5835 @ 80), (N/A, 30), (N/A)
>>>> (57240 - 63720 @ 2160), (N/A, 40), (N/A)
>>>>
>>>> phy#0
>>>> country US: DFS-FCC
>>>> (2402 - 2472 @ 40), (N/A, 30), (N/A)
>>>> (5170 - 5250 @ 80), (N/A, 23), (N/A), AUTO-BW
>>>> (5250 - 5330 @ 80), (N/A, 23), (0 ms), DFS, AUTO-BW
>>>> (5490 - 5730 @ 160), (N/A, 23), (0 ms), DFS
>>>> (5735 - 5835 @ 80), (N/A, 30), (N/A)
>>>> (57240 - 63720 @ 2160), (N/A, 40), (N/A)
>>>>
>>>>
>>>> Kind regards,
>>>> Met vriendelijke groeten,
>>>> Ralph Houthoofdt
>>>> Student industriële wetenschappen informatica
>>>>
>>>>
>>>> _______________________________________________
>>>> ath10k mailing list
>>>> ath10k at lists.infradead.org
>>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>>>
>>>
>>> --
>>> Ben Greear <greearb at candelatech.com>
>>> Candela Technologies Inc http://www.candelatech.com
>>>
>>> _______________________________________________
>>> ath10k mailing list
>>> ath10k at lists.infradead.org
>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>>
>>
>> --
>> Ben Greear <greearb at candelatech.com>
>> Candela Technologies Inc http://www.candelatech.com
>>
>
> --
> Ben Greear <greearb at candelatech.com>
> Candela Technologies Inc http://www.candelatech.com
>
--
Ben Greear <greearb at candelatech.com>
Candela Technologies Inc http://www.candelatech.com
More information about the ath10k
mailing list