QCA9880 slow performance adhoc/IBSS mode

Tue Feb 28 09:36:41 PST 2017

Dear Ben,

Thank you for your quick reply.

My mesh is running on channel 36  using VHT80 and a TX power of 20 dbm, the
maximum allowed according to my regulatory settings from iw reg get. The
hwmode is set as 11a.
I have also enable the following ht_capabilities on my radio in
/etc/config/wireless:

        list ht_capab 'short_gi_80'
        list ht_capab 'max-mpdu-11454'
        list ht_capab 'TX-STBC-2BY1'
        list ht_capab 'RX-STBC1'
        list ht_capab 'RX-ANTENNA-PATTERN'
        list ht_capab 'TX-ANTENNA-PATTERN'
        list ht_capab 'MAX-A-MPDU-LEN-EXP7'

I just finished running iperf3 from my laptop (2nd gen Core i7) to one of my
nodes. The results were indeed a bit different.
Iperf server was running on my node and my laptop was the client.
UDP:
Normal: average result of 221Mbit, which is pretty normal I think.
Reverse: average result of 41Mbit, which is better than the average 20Mbit I
got when running iperf3 using 2 nodes.
TCP:
Normal: average result of 49Mbit
Reverse: average result of 35.4Mbit

In terms of congestion, I'm not sure what you mean, but I'm in a low
populated area with few wireless access points. I disabled all my 5GHz
devices except for the mesh nodes. InSSIDer only shows my nodes in the 5GHz
range.

Is there anything else I could try for you?

Met vriendelijke groeten,
Ralph Houthoofdt
Student industriële wetenschappen informatica

-----Original Message-----
From: ath10k [mailto:ath10k-bounces at lists.infradead.org] On Behalf Of Ben
Greear
Sent: dinsdag 28 februari 2017 17:56
To: Ralph Houthoofdt <ralph at rora.be>; ath10k at lists.infradead.org
Subject: Re: QCA9880 slow performance adhoc/IBSS mode

Run iperf on a separate machine, as the apu2 have too weak of a CPU to drive
the wifi network at full speed.  And, publish what results you do get,
including RF information such as channel and how congested is your test
area.  Try udp as well as tcp.

Thanks,
Ben

On 02/28/2017 08:51 AM, Ralph Houthoofdt wrote:
> Dear all,
>
> I’m currently doing me masters thesis on the subject of Wireless Mesh 
> Networks and how to optimize them for home use.
> The devices I use are 5x PC Engine APU2c4 with 2x QCA9880 chip (Compex 
> WLE900VX). All of them are running LEDE (OpenWRT fork).
>
> The problem I’m experiencing is the same as 
> http://lists.infradead.org/pipermail/ath10k/2017-January/009075.html . 
> Using the tips mentioned I did not come to a better performance. I’m 
> thinking it’s driver related..
> When running iperf3 only one direction is running at a reasonable 
> throughput. Since I am using adhoc mode primarily I decided to use 
> these
> packages:
> -	Kmod-ath10k-ct
> -	Ath10k-firmware-qca988x-ct
> Some sources on the internet said that using the Candela Tech drivers 
> should result in better support for adhoc/mesh networks.
>
> As suggested in the other issue linked above, I switched TCP 
> congestion control to ‘Reno’ instead of the default ‘Cubic’.
> I also did try the command “iw reg set BE” since I am from Belgium, 
> but running “iw reg get” right after still gave me US as a result.
>
> Let me know what additional command info I should post. Any help would 
> be greatly appreciated.
>
> Iwconfig:
> adhoc0    IEEE 802.11  ESSID:"mesh"
>           Mode:Ad-Hoc  Frequency:5.18 GHz  Cell: 02:CA:FE:CA:CA:40
>           Tx-Power=20 dBm
>           RTS thr:off   Fragment thr:off
>           Encryption key:off
>           Power Management:off
>
>
> Iw reg get (I’m from Belgium):
> global
> country BE: DFS-ETSI
>         (2402 - 2482 @ 40), (N/A, 20), (N/A)
>         (5170 - 5250 @ 80), (N/A, 20), (N/A), AUTO-BW
>         (5250 - 5330 @ 80), (N/A, 20), (0 ms), DFS, AUTO-BW
>         (5490 - 5710 @ 160), (N/A, 27), (0 ms), DFS
>         (57000 - 66000 @ 2160), (N/A, 40), (N/A)
>
> phy#1
> country US: DFS-FCC
>         (2402 - 2472 @ 40), (N/A, 30), (N/A)
>         (5170 - 5250 @ 80), (N/A, 23), (N/A), AUTO-BW
>         (5250 - 5330 @ 80), (N/A, 23), (0 ms), DFS, AUTO-BW
>         (5490 - 5730 @ 160), (N/A, 23), (0 ms), DFS
>         (5735 - 5835 @ 80), (N/A, 30), (N/A)
>         (57240 - 63720 @ 2160), (N/A, 40), (N/A)
>
> phy#0
> country US: DFS-FCC
>         (2402 - 2472 @ 40), (N/A, 30), (N/A)
>         (5170 - 5250 @ 80), (N/A, 23), (N/A), AUTO-BW
>         (5250 - 5330 @ 80), (N/A, 23), (0 ms), DFS, AUTO-BW
>         (5490 - 5730 @ 160), (N/A, 23), (0 ms), DFS
>         (5735 - 5835 @ 80), (N/A, 30), (N/A)
>         (57240 - 63720 @ 2160), (N/A, 40), (N/A)
>
>
> Kind regards,
> Met vriendelijke groeten,
> Ralph Houthoofdt
> Student industriële wetenschappen informatica
>
>
> _______________________________________________
> ath10k mailing list
> ath10k at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/ath10k
>

--
Ben Greear <greearb at candelatech.com>
Candela Technologies Inc  http://www.candelatech.com

_______________________________________________
ath10k mailing list
ath10k at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k