Direct firmware load failed with error 2
cmckay at abineau.com
cmckay at abineau.com
Mon Oct 24 19:59:06 PDT 2016
Hi Ben
root at apalis-imx6:~# lspci -v
00:00.0 PCI bridge: Synopsys, Inc. Device abcd (rev 01) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 388
Memory at 01200000 (32-bit, non-prefetchable) [size=1M]
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: 01000000-011fffff
Prefetchable memory behind bridge: 01300000-013fffff
[virtual] Expansion ROM at 01400000 [disabled] [size=64K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable+ Count=1/1 Maskable+ 64bit+
Capabilities: [70] Express Root Port (Slot-), MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Kernel driver in use: pcieport
01:00.0 Network controller: Qualcomm Atheros QCA986x/988x 802.11ac Wireless Network Adapter
Flags: fast devsel, IRQ 155
Memory at 01000000 (64-bit, non-prefetchable) [size=2M]
[virtual] Expansion ROM at 01300000 [disabled] [size=64K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable- Count=8/8 Maskable+ 64bit-
Capabilities: [70] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Capabilities: [160] Device Serial Number 00-00-00-00-00-00-00-00
Kernel modules: ath10k_pci
----------
Angstrom v2015.12 - Kernel 3.14.52-v2.6b2+g7c83cef
Apalis_iMX6_LinuxImageV2.6_20160929
This is Toradex's standard build for their Apalis iMX6 on a Ixora carrier. I think they are due for a new major release very soon. I can check if you think it's worth it.
The current firmware is yours (firmware-2-ct-full-community.bin), fresh off your site today. I downloaded board.bin today too.
---------------
root at apalis-imx6:~# lsmod
Module Size Used by
usb_f_rndis 11441 2
u_ether 9135 1 usb_f_rndis
usb_f_acm 4105 2
u_serial 8487 1 usb_f_acm
ov5640_camera_mipi_int 21588 0
mxc_v4l2_capture 24990 1 ov5640_camera_mipi_int
ipu_bg_overlay_sdc 4113 1 mxc_v4l2_capture
ipu_still 1631 1 mxc_v4l2_capture
ipu_prp_enc 4653 1 mxc_v4l2_capture
max9526_tvin 5800 0
ipu_csi_enc 2917 1 mxc_v4l2_capture
ipu_fg_overlay_sdc 4978 1 mxc_v4l2_capture
adv7280_tvin 6563 0
v4l2_int_device 1759 4 adv7280_tvin,ov5640_camera_mipi_int,mxc_v4l2_capture,max9526_tvin
ath10k_pci 27397 0
ath10k_core 101131 1 ath10k_pci
ath 17381 1 ath10k_core
mac80211 254675 1 ath10k_core
cfg80211 166770 3 ath,mac80211,ath10k_core
libcomposite 28353 12 usb_f_acm,usb_f_rndis
configfs 20737 4 usb_f_acm,usb_f_rndis,libcomposite
galcore 207484 2
------------
root at apalis-imx6:~# ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: can0: <NOARP,ECHO> mtu 16 qdisc noop state DOWN mode DEFAULT group default qlen 10
link/can
3: can1: <NOARP,ECHO> mtu 16 qdisc noop state DOWN mode DEFAULT group default qlen 10
link/can
4: eth0: <BROADCAST,MULTICAST,DYNAMIC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group defaul0
link/ether 00:14:2d:4a:30:f9 brd ff:ff:ff:ff:ff:ff
5: sit0 at NONE: <NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default
link/sit 0.0.0.0 brd 0.0.0.0
6: usb0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default ql0
link/ether 00:14:2d:ff:ff:ff brd ff:ff:ff:ff:ff:ff
Thanks again,
Colin
-----Original Message-----
From: "Ben Greear" <greearb at candelatech.com>
Sent: Monday, October 24, 2016 9:57pm
To: cmckay at abineau.com
Cc: ath10k at lists.infradead.org
Subject: Re: Direct firmware load failed with error 2
Please let us know 'lspci' or equiv, exactly what firmware you are loading,
kernel driver version, etc.
Maybe try LEDE if you can, it's likely more up to date.
Thanks,
Ben
On 10/24/2016 04:22 PM, cmckay at abineau.com wrote:
> Great, thanks Ben,
>
> That cleared up the firmware load error but I now have:
>
> [ 6.997553] ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 0x01000000-0x011ff]
> [ 7.075559] ath10k: pci irq MSI
> [ 9.753487] ath10k: ctl_resp never came in (-110)
> [ 9.758281] ath10k: failed to connect to HTC: -110
> [ 9.803633] ath10k: could not init core (-110)
> [ 9.843495] ath10k: could not probe fw (-110)
> [ 9.843499] ath10k: failed to register driver core: -110
> [ 9.843681] ath10k_pci: probe of 0000:01:00.0 failed with error -110
>
> Any ideas? Let me know if I should post this new.
>
> Thanks a bunch
> Colin
>
>
> -----Original Message-----
> From: "Ben Greear" <greearb at candelatech.com>
> Sent: Monday, October 24, 2016 5:05pm
> To: cmckay at abineau.com
> Cc: ath10k at lists.infradead.org
> Subject: Re: Direct firmware load failed with error 2
>
> You need board.bin too. Something like this if you want to
> use my firmware, or firmware-5.bin for upstream 10.2 firmware:
>
> [root at ben-ota-1 lanforge]# ls -l /lib/firmware/ath10k/QCA988X/hw2.0/
> total 1084
> -rw-r--r--. 1 root root 2116 Sep 27 14:43 board.bin
> -rw-r--r--. 1 root root 201324 Oct 13 18:48 firmware-2.bin
>
> Thanks,
> Ben
>
>
> On 10/24/2016 01:59 PM, cmckay at abineau.com wrote:
>> Thanks Ben,
>>
>> Got the location from the website:
>> root at apalis-imx6:/lib/firmware/ath10k/QCA988X/hw2.0# ls
>> firmware-2.bin firmware-5.bin
>>
>> I'll figure out how to do some printk's (I'm a newbie).
>>
>> Thanks,
>> Colin
>>
>>
>> -----Original Message-----
>> From: "Ben Greear" <greearb at candelatech.com>
>> Sent: Monday, October 24, 2016 4:11pm
>> To: cmckay at abineau.com, ath10k at lists.infradead.org
>> Subject: Re: Direct firmware load failed with error 2
>>
>> Maybe add some printks in your driver to see exactly what it is trying to load?
>>
>> Maybe firmware is in wrong location?
>>
>> errno 2 == ENOENT, which probably means something like 'could not find file'.
>>
>> Thanks,
>> Ben
>>
>>
>> On 10/24/2016 12:55 PM, cmckay at abineau.com wrote:
>>> Hi,
>>>
>>> I'm attempting to add a Silex PCEAC or Compex WLE900VX (both QCA9880) mini PCIe card to a Toradex Apalis iMX6 SOM on their Ixora card. I added a BSP layer to Toradex's standard build, simply adding the ath10k and noting more.
>>> I keep running into the following error:
>>>
>>> [ 7.063663] ath10k_pci 0000:01:00.0: BAR 0: assigned [mem 0x01000000-0x011ff]
>>> [ 7.172118] ath10k: pci irq MSI
>>> [ 7.198024] ath10k_pci 0000:01:00.0: Direct firmware load failed with error 2
>>> [ 7.209646] ath10k_pci 0000:01:00.0: Falling back to user helper
>>> [ 8.626488] ath10k: could not fetch board data (-2)
>>> [ 8.648471] ath10k_pci 0000:01:00.0: Direct firmware load failed with error 2
>>> [ 8.693701] ath10k_pci 0000:01:00.0: Falling back to user helper
>>> [ 8.712302] ath10k: could not fetch board data (-2)
>>> [ 8.722757] ath10k: could not fetch firmware files (-2)
>>> [ 8.781868] ath10k: could not probe fw (-2)
>>> [ 8.781874] ath10k: failed to register driver core: -2
>>> [ 8.782041] ath10k_pci: probe of 0000:01:00.0 failed with error -2
>>>
>>> I've tried the firmware-2, firmware-5 and Candella firmware. I can't find any information on what this error means or how to debug this issue. And the vendors are struggling to get me a solution.
>>> Any help would be greatly appreciated.
>>>
>>> Colin McKay
>>>
>>>
>>>
>>> _______________________________________________
>>> ath10k mailing list
>>> ath10k at lists.infradead.org
>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>>
>>
>>
>
>
--
Ben Greear <greearb at candelatech.com>
Candela Technologies Inc http://www.candelatech.com
_______________________________________________
ath10k mailing list
ath10k at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
More information about the ath10k
mailing list