ath10k firmware crashes in mesh mode on QCA9880
Mohammed Shafi Shajakhan
mohammed at codeaurora.org
Sat Dec 3 04:43:58 PST 2016
Hi Benjamin,
On Fri, Dec 02, 2016 at 05:28:02PM -0800, Benjamin Morgan wrote:
> Just tried 10.2.4.70.58 firmware that you linked to and it still crashes:
>
> [ 131.568989] ath10k_pci 0000:01:00.0: firmware crashed! (uuid
> 1838347e-9380-4a26-ac9d-2963ee95968b)
> [ 131.578124] ath10k_pci 0000:01:00.0: qca988x hw2.0 target
> 0x4100016c chip_id 0x043202ff sub 0000:0000
> [ 131.587491] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1
> tracing 0 dfs 1 testmode 1
> [ 131.600521] ath10k_pci 0000:01:00.0: firmware ver 10.2.4.70.58
> api 5 features no-p2p,raw-mode,mfp crc32 e1af076f
> [ 131.610899] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A
> crc32 bebc7c08
> [ 131.618325] ath10k_pci 0000:01:00.0: htt-ver 2.1 wmi-op 5 htt-op
> 2 cal file max-sta 128 raw 0 hwcrypto 1
> [ 131.629965] ath10k_pci 0000:01:00.0: firmware register dump:
> [ 131.635728] ath10k_pci 0000:01:00.0: [00]: 0x4100016C 0x000015B3
> 0x009A45AF 0x00955B31
> [ 131.643761] ath10k_pci 0000:01:00.0: [04]: 0x009A45AF 0x00060130
> 0x00000002 0x00439E98
> [ 131.651806] ath10k_pci 0000:01:00.0: [08]: 0x0044110C 0x00442074
> 0x00407120 0x004436CC
> [ 131.659852] ath10k_pci 0000:01:00.0: [12]: 0x00000009 0x00000000
> 0x009A3550 0x009A355E
> [ 131.667892] ath10k_pci 0000:01:00.0: [16]: 0x00958080 0x009A31D6
> 0x00000000 0x00000000
> [ 131.675936] ath10k_pci 0000:01:00.0: [20]: 0x409A45AF 0x0040AAC4
> 0x0040AC60 0x0040AC09
> [ 131.683968] ath10k_pci 0000:01:00.0: [24]: 0x809A44F2 0x0040AB24
> 0x00400000 0xC09A45AF
> [ 131.692013] ath10k_pci 0000:01:00.0: [28]: 0x809A3A16 0x0040AB84
> 0x0044110C 0x00442074
> [ 131.700056] ath10k_pci 0000:01:00.0: [32]: 0x809A601A 0x0040ABB4
> 0x0044110C 0x00407120
> [ 131.708100] ath10k_pci 0000:01:00.0: [36]: 0x809A2EA4 0x0040ABF4
> 0x0040AC14 0x00001580
> [ 131.716143] ath10k_pci 0000:01:00.0: [40]: 0x80990F63 0x0040AD04
> 0x009C6458 0x004436CC
> [ 131.724175] ath10k_pci 0000:01:00.0: [44]: 0x80998520 0x0040AD64
> 0x004208FC 0x00439E4C
> [ 131.732220] ath10k_pci 0000:01:00.0: [48]: 0x8099AEA5 0x0040AD84
> 0x004208FC 0x00425874
> [ 131.740263] ath10k_pci 0000:01:00.0: [52]: 0x809BFC39 0x0040AEE4
> 0x00424FE8 0x00000002
> [ 131.748306] ath10k_pci 0000:01:00.0: [56]: 0x80940F18 0x0040AF14
> 0x00000004 0x004039D0
> [ 131.857076] ieee80211 phy0: Hardware restart was requested
> [ 131.862705] ath10k_pci 0000:01:00.0: failed to synchronize
> monitor vdev 1 stop: -143
> [ 131.870594] ath10k_pci 0000:01:00.0: failed to stop monitor vdev: -143
[shafi] request to try with the latest backports and ath.git
Also worth trying this fix in ath10k (once the next firmware version)
is available. I will keep you posted. thank you !
>
> ~Benjamin
>
> On 11/30/2016 11:09 PM, Mohammed Shafi Shajakhan wrote:
> >Hi,
> >
> >On Tue, Nov 29, 2016 at 11:22:12AM -0800, Benjamin Morgan wrote:
> >>When we try to transmit traffic (ping) between two meshed ath10k
> >>devices running latest lede we keep experiencing ath10k firmware
> >>crashes. This seems to only happen when running in 802.11n/ac mode
> >>but not in 802.11a/g mode. Also, from the station dumps it appears
> >>that management traffic is flowing between the devices, however when
> >>we try to send unicast data traffic the firmware crashes
> >>immediately.
> >[shafi] Did you get a chance to try with the below firmware as well
> >https://github.com/kvalo/ath10k-firmware/blob/master/QCA988X/hw2.0/10.2.4.70/firmware-5.bin_10.2.4.70.58
> >
> >>Platform: Archer C7 AC1750 v2
> >>Software Image: LEDE (HEAD, r2299) Commit: https://github.com/lede-project/source/commit/d596c21ebd5a3e6ce933eff3e51989031e4b1d58
> >>
> >>Crypto: wpa_supplicant
> >>wpa_supplicant-wlan0.conf
> >>network={
> >>ssid="bmorgan_lede_mesh"
> >>key_mgmt=SAE
> >>mode=5
> >>frequency=5180
> >>psk="meshpassword"
> >>}
> >>
> >>Backports Verstion:
> >>[ 9.818007] Loading modules backported from Linux version
> >>wt-2016-10-03-1-g6fcb1a6
> >>[ 9.825736] Backport generated by backports.git
> >>backports-20160324-9-g0e38f5c
> >>
> >>Ath10k Initialization on Station A (dmesg)
> >>[ 9.896715] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
> >>[ 9.902622] ath10k_pci 0000:01:00.0: pci irq legacy oper_irq_mode
> >>1 irq_mode 0 reset_mode 0
> >>[ 10.123734] ath10k_pci 0000:01:00.0: Direct firmware load for
> >>ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2
> >>[ 10.134620] ath10k_pci 0000:01:00.0: Falling back to user helper
> >>[ 10.287680] firmware ath10k!pre-cal-pci-0000:01:00.0.bin:
> >>firmware_loading_store: map pages failed
> >>[ 10.622789] ath10k_pci 0000:01:00.0: qca988x hw2.0 target
> >>0x4100016c chip_id 0x043202ff sub 0000:0000
> >>[ 10.632184] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1
> >>tracing 0 dfs 1 testmode 1
> >>[ 10.645231] ath10k_pci 0000:01:00.0: firmware ver 10.2.4.70.54
> >>api 5 features no-p2p,raw-mode,mfp crc32 9d340dd9
> >>[ 10.655660] ath10k_pci 0000:01:00.0: Direct firmware load for
> >>ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
> >>[ 10.666264] ath10k_pci 0000:01:00.0: Falling back to user helper
> >>[ 10.747925] firmware ath10k!QCA988X!hw2.0!board-2.bin:
> >>firmware_loading_store: map pages failed
> >>[ 11.011123] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A
> >>crc32 bebc7c08
> >>[ 12.155224] ath10k_pci 0000:01:00.0: htt-ver 2.1 wmi-op 5 htt-op
> >>2 cal file max-sta 128 raw 0 hwcrypto 1
> >>
> >>Station A (wlan0):
> >>18:A6:F7:23:6E:66
> >>10.230.5.41
> >>
> >>Station B (wlan0):
> >>18:a6:f7:26:0f:21
> >>10.230.5.42
> >>
> >>Station Dump on Station A before ping:
> >>Station 18:a6:f7:26:0f:21 (on wlan0)
> >>inactive time:340 ms
> >>rx bytes:2472
> >>rx packets:28
> >>tx bytes:1204
> >>tx packets:9
> >>tx retries:0
> >>tx failed:0
> >>rx drop misc:1
> >>signal: -14 dBm
> >>signal avg:-14 dBm
> >>Toffset:18142530 us
> >>tx bitrate:6.0 MBit/s
> >>rx bitrate:6.0 MBit/s
> >>rx duration:1524 us
> >>mesh llid:0
> >>mesh plid:0
> >>mesh plink:ESTAB
> >>mesh local PS mode:ACTIVE
> >>mesh peer PS mode:UNKNOWN
> >>mesh non-peer PS mode:ACTIVE
> >>authorized:yes
> >>authenticated:yes
> >>associated:yes
> >>preamble:long
> >>WMM/WME:yes
> >>MFP:yes
> >>TDLS peer:no
> >>DTIM period:2
> >>beacon interval:1000
> >>connected time:10 seconds
> >>
> >>Crash Log on Station B (10.230.5.42)
> >>[245.483888] ath10k_pci 0000:01:00.0: firmware crashed! (uuid
> >>2bab5ee9-08ff-4a17-95b1-636d212acebc)
> >>[245.493020] ath10k_pci 0000:01:00.0: qca988x hw2.0 target
> >>0x4100016c chip_id 0x043202ff sub 0000:0000
> >>[245.502384] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1
> >>tracing 0 dfs 1 testmode 1
> >>[245.515436] ath10k_pci 0000:01:00.0: firmware ver 10.2.4.70.54 api
> >>5 features no-p2p,raw-mode,mfp crc32 9d340dd9
> >>[245.525812] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A
> >>crc32 bebc7c08
> >>[245.533232] ath10k_pci 0000:01:00.0: htt-ver 2.1 wmi-op 5 htt-op 2
> >>cal file max-sta 128 raw 0 hwcrypto 1
> >>[245.544876] ath10k_pci 0000:01:00.0: firmware register dump:
> >>[245.550633] ath10k_pci 0000:01:00.0: [00]: 0x4100016C 0x000015B3
> >>0x009A4577 0x00955B31
> >>[245.558676] ath10k_pci 0000:01:00.0: [04]: 0x009A4577 0x00060130
> >>0x00000002 0x00439E98
> >>[245.566715] ath10k_pci 0000:01:00.0: [08]: 0x0044110C 0x00442074
> >>0x00407120 0x004436CC
> >>[245.574749] ath10k_pci 0000:01:00.0: [12]: 0x00000009 0x00000000
> >>0x009A3518 0x009A3526
> >>[245.582793] ath10k_pci 0000:01:00.0: [16]: 0x00958080 0x0094085D
> >>0x00000000 0x00000000
> >>[245.590836] ath10k_pci 0000:01:00.0: [20]: 0x409A4577 0x0040AAC4
> >>0x0040AC60 0x0040AC09
> >>[245.598882] ath10k_pci 0000:01:00.0: [24]: 0x809A44BA 0x0040AB24
> >>0x00400000 0xC09A4577
> >>[245.606923] ath10k_pci 0000:01:00.0: [28]: 0x809A39DE 0x0040AB84
> >>0x0044110C 0x00442074
> >>[245.614955] ath10k_pci 0000:01:00.0: [32]: 0x809A5FE2 0x0040ABB4
> >>0x0044110C 0x00407120
> >>[245.623000] ath10k_pci 0000:01:00.0: [36]: 0x809A2E6C 0x0040ABF4
> >>0x0040AC14 0x00001580
> >>[245.631043] ath10k_pci 0000:01:00.0: [40]: 0x80990F6F 0x0040AD04
> >>0x009C643C 0x004436CC
> >>[245.639086] ath10k_pci 0000:01:00.0: [44]: 0x80998510 0x0040AD64
> >>0x004208FC 0x00439E4C
> >>[245.647129] ath10k_pci 0000:01:00.0: [48]: 0x8099AE95 0x0040AD84
> >>0x004208FC 0x00425404
> >>[245.655170] ath10k_pci 0000:01:00.0: [52]: 0x809BFC55 0x0040AEE4
> >>0x00424FE8 0x00000002
> >>[245.663198] ath10k_pci 0000:01:00.0: [56]: 0x80940F18 0x0040AF14
> >>0x00000004 0x004039D0
> >>[245.767023] ieee80211 phy0: Hardware restart was requested
> >>[245.772655] ath10k_pci 0000:01:00.0: failed to synchronize monitor
> >>vdev 1 stop: -143
> >>[245.780542] ath10k_pci 0000:01:00.0: failed to stop monitor vdev: -143
> >>
> >>With wpa_supplicant turned off:
> >>
> >>Station Dump on Station A before ping:
> >>Station 18:a6:f7:26:0f:21 (on wlan0)
> >>inactive time:60 ms
> >>rx bytes:3874
> >>rx packets:67
> >>tx bytes:707
> >>tx packets:7
> >>tx retries:0
> >>tx failed:1
> >>rx drop misc:3
> >>signal: -14 dBm
> >>signal avg:-14 dBm
> >>Toffset:18446744073684250999 us
> >>tx bitrate:6.0 MBit/s
> >>rx bitrate:6.0 MBit/s
> >>rx duration:1312 us
> >>mesh llid:24953
> >>mesh plid:59412
> >>mesh plink:ESTAB
> >>mesh local PS mode:ACTIVE
> >>mesh peer PS mode:UNKNOWN
> >>mesh non-peer PS mode:ACTIVE
> >>authorized:yes
> >>authenticated:yes
> >>associated:yes
> >>preamble:long
> >>WMM/WME:yes
> >>MFP:no
> >>TDLS peer:no
> >>DTIM period:2
> >>beacon interval:1000
> >>short slot time:yes
> >>connected time:33 seconds
> >>
> >>Firmware crash on Station A (10.230.5.41)
> >>[ 1040.984599] ath10k_pci 0000:01:00.0: firmware crashed! (uuid
> >>42d4f6dc-0e89-4505-aefb-58cbb70d0dce)
> >>[ 1040.993732] ath10k_pci 0000:01:00.0: qca988x hw2.0 target
> >>0x4100016c chip_id 0x043202ff sub 0000:0000
> >>[ 1041.003100] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1
> >>tracing 0 dfs 1 testmode 1
> >>[ 1041.016144] ath10k_pci 0000:01:00.0: firmware ver 10.2.4.70.54
> >>api 5 features no-p2p,raw-mode,mfp crc32 9d340dd9
> >>[ 1041.026523] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A
> >>crc32 bebc7c08
> >>[ 1041.033940] ath10k_pci 0000:01:00.0: htt-ver 2.1 wmi-op 5 htt-op
> >>2 cal file max-sta 128 raw 0 hwcrypto 1
> >>[ 1041.045593] ath10k_pci 0000:01:00.0: firmware register dump:
> >>[ 1041.051336] ath10k_pci 0000:01:00.0: [00]: 0x4100016C 0x000015B3
> >>0x009A4577 0x00955B31
> >>[ 1041.059383] ath10k_pci 0000:01:00.0: [04]: 0x009A4577 0x00060130
> >>0x00000001 0x00435354
> >>[ 1041.067424] ath10k_pci 0000:01:00.0: [08]: 0x0044110C 0x00442074
> >>0x00407120 0x004436CC
> >>[ 1041.075463] ath10k_pci 0000:01:00.0: [12]: 0x00000009 0x00000000
> >>0x009A43A0 0x009A43DE
> >>[ 1041.083490] ath10k_pci 0000:01:00.0: [16]: 0x00958080 0x0094085D
> >>0x00000000 0x00000000
> >>[ 1041.091535] ath10k_pci 0000:01:00.0: [20]: 0x409A4577 0x0040AAC4
> >>0x0040AC60 0x0040AC09
> >>[ 1041.099579] ath10k_pci 0000:01:00.0: [24]: 0x809A44BA 0x0040AB24
> >>0x00955A00 0xC09A4577
> >>[ 1041.107622] ath10k_pci 0000:01:00.0: [28]: 0x809A39DE 0x0040AB84
> >>0x0044110C 0x00442074
> >>[ 1041.115661] ath10k_pci 0000:01:00.0: [32]: 0x809A5FE2 0x0040ABB4
> >>0x0044110C 0x00407120
> >>[ 1041.123689] ath10k_pci 0000:01:00.0: [36]: 0x809A2E6C 0x0040ABF4
> >>0x0040AC10 0x00001580
> >>[ 1041.131733] ath10k_pci 0000:01:00.0: [40]: 0x80990F6F 0x0040AD04
> >>0x009C643C 0x004436CC
> >>[ 1041.139777] ath10k_pci 0000:01:00.0: [44]: 0x80998510 0x0040AD64
> >>0x004208FC 0x00439E4C
> >>[ 1041.147820] ath10k_pci 0000:01:00.0: [48]: 0x8099AE95 0x0040AD84
> >>0x004208FC 0x00425758
> >>[ 1041.155860] ath10k_pci 0000:01:00.0: [52]: 0x809BFC55 0x0040AEE4
> >>0x00424FE8 0x00000002
> >>[ 1041.163888] ath10k_pci 0000:01:00.0: [56]: 0x80940F18 0x0040AF14
> >>0x00000004 0x004039D0
> >>[ 1041.267025] ieee80211 phy0: Hardware restart was requested
> >>[ 1041.272656] ath10k_pci 0000:01:00.0: failed to synchronize
> >>monitor vdev 1 stop: -143
> >>[ 1041.280545] ath10k_pci 0000:01:00.0: failed to stop monitor vdev: -143
> >>
> >>
> >>Thanks in advance for your time and help,
> >>
> >>~Benjamin
> >>
>
More information about the ath10k
mailing list