[SPAM] Re: WLE600VX from PCEngines
Jorge Baranda
jbaranda at cttc.es
Wed Sep 9 04:08:24 PDT 2015
Hi,
Good news!! Harms, could you share full wpa_supplicant configuration files?
(for both computers).
I will download the latest version of wpa_supplicant, apply your changes
and try
to make work IBSS mode and 80MHz with Candela Kernel 4.0.
Thanks,
El 09/09/15 12:59, Harms, Hannes escribió:
> Hi,
>
> I have WLE900VX working in IBSS mode and 80 Mhz with Candela Kernel 4.2.
> For me also the latest wpa_supplicant was not able to activate 80MHz
> by default , I don't no why.
>
> The only way I found to get it working was to modify
> wpa_supplicant/wpa_supplicant.c
> Commit following two lines in wpa_supplicant.c like this :
>
> //if (!(wpa_s->drv_flags & WPA_DRIVER_FLAGS_VHT_IBSS))
> // return;
>
> That was all for me to get it working.
>
> wpa_supplicant config file:
> # Use libnl 3.2 libraries (if this is selected, CONFIG_LIBNL20 is
> ignored)
> CONFIG_LIBNL32=y
>
> # Support VHT overrides (disable VHT, mask MCS rates, etc.)
> CONFIG_VHT_OVERRIDES=y
>
> # Support HT overrides (disable HT/HT40, mask MCS rates, etc.)
> CONFIG_HT_OVERRIDES=y
>
> # IEEE 802.11n (High Throughput) support (mainly for AP mode)
> CONFIG_IEEE80211N=y
>
> # IEEE 802.11ac (Very High Throughput) support (mainly for AP mode)
> # (depends on CONFIG_IEEE80211N)
> CONFIG_IEEE80211AC=y
>
> # IEEE 802.11w (management frame protection), also known as PMF
> # Driver support is also needed for IEEE 802.11w.
> CONFIG_IEEE80211W=y
>
> Am 09.09.2015 um 11:46 schrieb Marcel H.:
>> May I ask someone for support on this one?
>> We would really like to make this work and I'm running out of ideas -
>> is there any way do turn detailed debugging on to get a better
>> understanding why do I get the following message back? ->
>>
>> root at voyage1:/opt/ca_node/etc# iw wlan0 set freq 5745 80 5775
>> command failed: Device or resource busy (-16)
>>
>> Thanks,
>> Marcel
>>
>> On Wed, Sep 9, 2015 at 9:49 AM, Marcel H. <maco at blava.net> wrote:
>>> Thanks for the response, unfortunately this is the result of defining
>>> the center frequency:
>>>
>>> root at voyage1:/opt/ca_node/etc# iw wlan0 set freq 5745 80 5775
>>> command failed: Device or resource busy (-16)
>>>
>>> Also, using wpa_supplicant does not work using the following config:
>>>
>>> root at voyage1:/opt/ca_node/etc# cat wpa_supplicant-mesh.conf
>>> ap_scan=2
>>> ctrl_interface=/run/wpa_supplicant
>>> update_config=1
>>> device_type=0-00000000-0
>>>
>>> network={
>>> scan_ssid=1
>>> key_mgmt=NONE
>>> priority=1
>>> ssid="ibss"
>>> mode=1
>>> frequency=5180
>>> }
>>>
>>> running as:
>>> wpa_supplicant -i wlan0 -c ./wpa_supplicant-mesh.conf -dd -D
>>> nl80211,wext
>>>
>>>
>>>
>>> root at voyage1:/opt/ca_node/etc# iw dev wlan0 info
>>> Interface wlan0
>>> ifindex 5
>>> wdev 0x100000001
>>> addr 04:f0:21:1b:5f:3d
>>> ssid ibss-rsn
>>> type IBSS
>>> wiphy 1
>>> channel 36 (5180 MHz), width: 20 MHz, center1: 5180 MHz
>>>
>>> root at voyage1:/opt/ca_node/etc# iw phy phy1 info
>>> Wiphy phy1
>>> DFS state: usable (for 46424 sec)
>>> DFS CAC time: 60000 ms
>>> * 5280 MHz [56] (23.0 dBm) (no IR, radar
>>> detection)
>>> DFS state: usable (for 46424 sec)
>>> DFS CAC time: 60000 ms
>>> * 5300 MHz [60] (23.0 dBm) (no IR, radar
>>> detection)
>>> DFS state: usable (for 46424 sec)
>>> DFS CAC time: 60000 ms
>>> * 5320 MHz [64] (23.0 dBm) (no IR, radar
>>> detection)
>>> DFS state: usable (for 46424 sec)
>>> Its fallbacking to 20MHz channels, which is even less than 40MHz
>>> channels set manually by iw
>>>
>>>
>>> How recent wpa_supplicat shall I try? I believe this it quite recent:
>>>
>>> root at voyage1:/opt/ca_node/etc# wpa_supplicant -v
>>> wpa_supplicant v2.3
>>> Copyright (c) 2003-2014, Jouni Malinen <j at w1.fi> and contributors
>>>
>>>
>>> Re. the regulatory settings:
>>>
>>> root at voyage1:/opt/ca_node/etc# iw reg get
>>> country US: DFS-FCC
>>> (2402 - 2472 @ 40), (N/A, 30), (N/A)
>>> (5170 - 5250 @ 80), (N/A, 17), (N/A)
>>> (5250 - 5330 @ 80), (N/A, 23), (0 ms), DFS
>>> (5735 - 5835 @ 80), (N/A, 30), (N/A)
>>> (57240 - 63720 @ 2160), (N/A, 40), (N/A)
>>>
>>>
>>> Any other thoughts?
>>>
>>> Marcel
>>>
>>> On Wed, Sep 9, 2015 at 9:43 AM, Janusz Dziedzic
>>> <janusz.dziedzic at tieto.com> wrote:
>>>> On 9 September 2015 at 08:20, Jorge Baranda <jbaranda at cttc.es> wrote:
>>>>> Hi everyone,
>>>>>
>>>>> Reading this thread, I would like to share with people some doubts
>>>>> about it.
>>>>> @Marco, I imagine you want to run your WLE600VX device using the
>>>>> 802.11ac
>>>>> protocol, isn't it?
>>>>> @Janusz, with running wpa_supplicant on both computers, will the
>>>>> ad-hoc
>>>>> connection be established? I am starting with these tools and now,
>>>>> I am
>>>>> getting used to know how they work. I was creating the ad-hoc
>>>>> connection
>>>>> with the iw tool.
>>>>>
>>>> Yes you should use wpa_supplicant on both PC.
>>>> In the future probably someone will add IBSS-VHT support also for iw.
>>>>
>>>> BR
>>>> Janusz
>>>>
>>>>> Thanks,
>>>>>
>>>>>
>>>>>
>>>>> El 09/09/15 07:50, Janusz Dziedzic escribió:
>>>>>
>>>>>> On 8 September 2015 at 23:31, Marcel H. <maco at blava.net> wrote:
>>>>>>> Hi everyone,
>>>>>>> I have an interesting issue - I'm trying to run the QCA9882
>>>>>>> based card
>>>>>>> in IBSS mode (to be used for BATMAN), however all I can do is to
>>>>>>> run
>>>>>>> in in 40Mhz channel width in 5GHz spectrum. Any attempt to run
>>>>>>> it in
>>>>>>> 80MHz width resolves in the following:
>>>>>>>
>>>>>> You should run IBSS using fresh wpa_supplicant (best latest
>>>>>> code). By
>>>>>> default should run in 80MHz.
>>>>>> Other case is your regulatory - are you allow to use 80MHz on
>>>>>> channel
>>>>>> 157? First try 5180.
>>>>>>
>>>>>> eg. of wpa_supplicant config:
>>>>>>
>>>>>> network = {
>>>>>> ssid="test_ibss"
>>>>>> key_mgmt=NONE
>>>>>> mode=1
>>>>>> frequency=5180
>>>>>> }
>>>>>>
>>>>>> BR
>>>>>> Janusz
>>>>>>
>>>>>>> Interface wlan0
>>>>>>> ifindex 5
>>>>>>> wdev 0x1
>>>>>>> addr 04:f0:21:1b:5f:3b
>>>>>>> ssid my-mesh-network
>>>>>>> type IBSS
>>>>>>> wiphy 0
>>>>>>> channel 157 (5785 MHz), width: 40 MHz, center1: 5795 MHz
>>>>>>> root at voyage2:/opt/ca_node/bin# iw dev wlan0 set freq 5745 80
>>>>>>> command failed: Invalid argument (-22)
>>>>>>> root at voyage2:/opt/ca_node/bin# ip link set wlan0 down
>>>>>>> root at voyage2:/opt/ca_node/bin# iw dev wlan0 set freq 5745 80
>>>>>>> command failed: Invalid argument (-22)
>>>>>>>
>>>>>>>
>>>>>>> More info:
>>>>>>> =====================================================
>>>>>>> 06:00.0 Network controller: Qualcomm Atheros QCA988x 802.11ac
>>>>>>> Wireless
>>>>>>> Network Adapter
>>>>>>> Flags: bus master, fast devsel, latency 0, IRQ 27
>>>>>>> Memory at f7400000 (64-bit, non-prefetchable) [size=2M]
>>>>>>> Expansion ROM at f7600000 [disabled] [size=64K]
>>>>>>> Capabilities: [40] Power Management version 2
>>>>>>> Capabilities: [50] MSI: Enable+ Count=1/8 Maskable+ 64bit-
>>>>>>> Capabilities: [70] Express Endpoint, MSI 00
>>>>>>> Capabilities: [100] Advanced Error Reporting
>>>>>>> Capabilities: [140] Virtual Channel
>>>>>>> Capabilities: [160] Device Serial Number
>>>>>>> 00-00-00-00-00-00-00-00
>>>>>>> Kernel driver in use: ath10k_pci
>>>>>>>
>>>>>>> root at voyage2:/opt/ca_node/bin# iw reg get
>>>>>>> country US: DFS-FCC
>>>>>>> (2402 - 2472 @ 40), (N/A, 30), (N/A)
>>>>>>> (5170 - 5250 @ 80), (N/A, 17), (N/A)
>>>>>>> (5250 - 5330 @ 80), (N/A, 23), (0 ms), DFS
>>>>>>> (5735 - 5835 @ 80), (N/A, 30), (N/A)
>>>>>>> (57240 - 63720 @ 2160), (N/A, 40), (N/A)
>>>>>>>
>>>>>>>
>>>>>>> root at voyage2:/opt/ca_node/bin# uname -a
>>>>>>> Linux voyage2 4.2.0-wl-ath-261216-gd89281c #1 SMP Tue Sep 8
>>>>>>> 14:03:33
>>>>>>> GMT 2015 i686 GNU/Linux
>>>>>>> (todays checkout from https://github.com/kvalo/ath + Voyage
>>>>>>> Linux 0.10
>>>>>>> .config)
>>>>>>>
>>>>>>> root at voyage2:/lib/firmware/ath10k/QCA988X/hw2.0# md5sum
>>>>>>> ./firmware-2.bin
>>>>>>> e2db04b651c2b5ced4732f3f009a1cce ./firmware-2.bin
>>>>>>> (this is from the 'main' directory in the
>>>>>>> https://github.com/kvalo/ath10k-firmware)
>>>>>>>
>>>>>>>
>>>>>>> Wiphy phy0
>>>>>>> max # scan SSIDs: 16
>>>>>>> max scan IEs length: 195 bytes
>>>>>>> Retry short limit: 7
>>>>>>> Retry long limit: 4
>>>>>>> Coverage class: 0 (up to 0m)
>>>>>>> Device supports RSN-IBSS.
>>>>>>> Device supports AP-side u-APSD.
>>>>>>> Supported Ciphers:
>>>>>>> * WEP40 (00-0f-ac:1)
>>>>>>> * WEP104 (00-0f-ac:5)
>>>>>>> * TKIP (00-0f-ac:2)
>>>>>>> * CCMP (00-0f-ac:4)
>>>>>>> * CMAC (00-0f-ac:6)
>>>>>>> Available Antennas: TX 0x3 RX 0x3
>>>>>>> Configured Antennas: TX 0x3 RX 0x3
>>>>>>> Supported interface modes:
>>>>>>> * IBSS
>>>>>>> * managed
>>>>>>> * AP
>>>>>>> * AP/VLAN
>>>>>>> * monitor
>>>>>>> * P2P-client
>>>>>>> * P2P-GO
>>>>>>> * P2P-device
>>>>>>> Band 1:
>>>>>>> Capabilities: 0x19e3
>>>>>>> RX LDPC
>>>>>>> HT20/HT40
>>>>>>> Static SM Power Save
>>>>>>> RX HT20 SGI
>>>>>>> RX HT40 SGI
>>>>>>> TX STBC
>>>>>>> RX STBC 1-stream
>>>>>>> Max AMSDU length: 7935 bytes
>>>>>>> DSSS/CCK HT40
>>>>>>> Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
>>>>>>> Minimum RX AMPDU time spacing: 8 usec (0x06)
>>>>>>> HT TX/RX MCS rate indexes supported: 0-15
>>>>>>> VHT Capabilities (0x338001b2):
>>>>>>> Max MPDU length: 11454
>>>>>>> Supported Channel Width: neither 160 nor 80+80
>>>>>>> RX LDPC
>>>>>>> short GI (80 MHz)
>>>>>>> TX STBC
>>>>>>> RX antenna pattern consistency
>>>>>>> TX antenna pattern consistency
>>>>>>> VHT RX MCS set:
>>>>>>> 1 streams: MCS 0-9
>>>>>>> 2 streams: MCS 0-9
>>>>>>> 3 streams: not supported
>>>>>>> 4 streams: not supported
>>>>>>> 5 streams: not supported
>>>>>>> 6 streams: not supported
>>>>>>> 7 streams: not supported
>>>>>>> 8 streams: not supported
>>>>>>> VHT RX highest supported: 0 Mbps
>>>>>>> VHT TX MCS set:
>>>>>>> 1 streams: MCS 0-9
>>>>>>> 2 streams: MCS 0-9
>>>>>>> 3 streams: not supported
>>>>>>> 4 streams: not supported
>>>>>>> 5 streams: not supported
>>>>>>> 6 streams: not supported
>>>>>>> 7 streams: not supported
>>>>>>> 8 streams: not supported
>>>>>>> VHT TX highest supported: 0 Mbps
>>>>>>> Bitrates (non-HT):
>>>>>>> * 1.0 Mbps
>>>>>>> * 2.0 Mbps (short preamble supported)
>>>>>>> * 5.5 Mbps (short preamble supported)
>>>>>>> * 11.0 Mbps (short preamble supported)
>>>>>>> * 6.0 Mbps
>>>>>>> * 9.0 Mbps
>>>>>>> * 12.0 Mbps
>>>>>>> * 18.0 Mbps
>>>>>>> * 24.0 Mbps
>>>>>>> * 36.0 Mbps
>>>>>>> * 48.0 Mbps
>>>>>>> * 54.0 Mbps
>>>>>>> Frequencies:
>>>>>>> * 2412 MHz [1] (30.0 dBm)
>>>>>>> * 2417 MHz [2] (30.0 dBm)
>>>>>>> * 2422 MHz [3] (30.0 dBm)
>>>>>>> * 2427 MHz [4] (30.0 dBm)
>>>>>>> * 2432 MHz [5] (30.0 dBm)
>>>>>>> * 2437 MHz [6] (30.0 dBm)
>>>>>>> * 2442 MHz [7] (30.0 dBm)
>>>>>>> * 2447 MHz [8] (30.0 dBm)
>>>>>>> * 2452 MHz [9] (30.0 dBm)
>>>>>>> * 2457 MHz [10] (30.0 dBm)
>>>>>>> * 2462 MHz [11] (30.0 dBm)
>>>>>>> * 2467 MHz [12] (disabled)
>>>>>>> * 2472 MHz [13] (disabled)
>>>>>>> * 2484 MHz [14] (disabled)
>>>>>>> Band 2:
>>>>>>> Capabilities: 0x19e3
>>>>>>> RX LDPC
>>>>>>> HT20/HT40
>>>>>>> Static SM Power Save
>>>>>>> RX HT20 SGI
>>>>>>> RX HT40 SGI
>>>>>>> TX STBC
>>>>>>> RX STBC 1-stream
>>>>>>> Max AMSDU length: 7935 bytes
>>>>>>> DSSS/CCK HT40
>>>>>>> Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
>>>>>>> Minimum RX AMPDU time spacing: 8 usec (0x06)
>>>>>>> HT TX/RX MCS rate indexes supported: 0-15
>>>>>>> VHT Capabilities (0x338001b2):
>>>>>>> Max MPDU length: 11454
>>>>>>> Supported Channel Width: neither 160 nor 80+80
>>>>>>> RX LDPC
>>>>>>> short GI (80 MHz)
>>>>>>> TX STBC
>>>>>>> RX antenna pattern consistency
>>>>>>> TX antenna pattern consistency
>>>>>>> VHT RX MCS set:
>>>>>>> 1 streams: MCS 0-9
>>>>>>> 2 streams: MCS 0-9
>>>>>>> 3 streams: not supported
>>>>>>> 4 streams: not supported
>>>>>>> 5 streams: not supported
>>>>>>> 6 streams: not supported
>>>>>>> 7 streams: not supported
>>>>>>> 8 streams: not supported
>>>>>>> VHT RX highest supported: 0 Mbps
>>>>>>> VHT TX MCS set:
>>>>>>> 1 streams: MCS 0-9
>>>>>>> 2 streams: MCS 0-9
>>>>>>> 3 streams: not supported
>>>>>>> 4 streams: not supported
>>>>>>> 5 streams: not supported
>>>>>>> 6 streams: not supported
>>>>>>> 7 streams: not supported
>>>>>>> 8 streams: not supported
>>>>>>> VHT TX highest supported: 0 Mbps
>>>>>>> Bitrates (non-HT):
>>>>>>> * 6.0 Mbps
>>>>>>> * 9.0 Mbps
>>>>>>> * 12.0 Mbps
>>>>>>> * 18.0 Mbps
>>>>>>> * 24.0 Mbps
>>>>>>> * 36.0 Mbps
>>>>>>> * 48.0 Mbps
>>>>>>> * 54.0 Mbps
>>>>>>> Frequencies:
>>>>>>> * 5180 MHz [36] (17.0 dBm)
>>>>>>> * 5200 MHz [40] (17.0 dBm)
>>>>>>> * 5220 MHz [44] (17.0 dBm)
>>>>>>> * 5240 MHz [48] (17.0 dBm)
>>>>>>> * 5260 MHz [52] (23.0 dBm) (no IR, radar detection)
>>>>>>> DFS state: usable (for 1076 sec)
>>>>>>> DFS CAC time: 60000 ms
>>>>>>> * 5280 MHz [56] (23.0 dBm) (no IR, radar detection)
>>>>>>> DFS state: usable (for 1076 sec)
>>>>>>> DFS CAC time: 60000 ms
>>>>>>> * 5300 MHz [60] (23.0 dBm) (no IR, radar detection)
>>>>>>> DFS state: usable (for 1076 sec)
>>>>>>> DFS CAC time: 60000 ms
>>>>>>> * 5320 MHz [64] (23.0 dBm) (no IR, radar detection)
>>>>>>> DFS state: usable (for 1076 sec)
>>>>>>> DFS CAC time: 60000 ms
>>>>>>> * 5500 MHz [100] (disabled)
>>>>>>> * 5520 MHz [104] (disabled)
>>>>>>> * 5540 MHz [108] (disabled)
>>>>>>> * 5560 MHz [112] (disabled)
>>>>>>> * 5580 MHz [116] (disabled)
>>>>>>> * 5600 MHz [120] (disabled)
>>>>>>> * 5620 MHz [124] (disabled)
>>>>>>> * 5640 MHz [128] (disabled)
>>>>>>> * 5660 MHz [132] (disabled)
>>>>>>> * 5680 MHz [136] (disabled)
>>>>>>> * 5700 MHz [140] (disabled)
>>>>>>> * 5720 MHz [144] (disabled)
>>>>>>> * 5745 MHz [149] (30.0 dBm)
>>>>>>> * 5765 MHz [153] (30.0 dBm)
>>>>>>> * 5785 MHz [157] (30.0 dBm)
>>>>>>> * 5805 MHz [161] (30.0 dBm)
>>>>>>> * 5825 MHz [165] (30.0 dBm)
>>>>>>> Supported commands:
>>>>>>> * new_interface
>>>>>>> * set_interface
>>>>>>> * new_key
>>>>>>> * start_ap
>>>>>>> * new_station
>>>>>>> * set_bss
>>>>>>> * authenticate
>>>>>>> * associate
>>>>>>> * deauthenticate
>>>>>>> * disassociate
>>>>>>> * join_ibss
>>>>>>> * remain_on_channel
>>>>>>> * set_tx_bitrate_mask
>>>>>>> * frame
>>>>>>> * frame_wait_cancel
>>>>>>> * set_wiphy_netns
>>>>>>> * set_channel
>>>>>>> * set_wds_peer
>>>>>>> * probe_client
>>>>>>> * set_noack_map
>>>>>>> * register_beacons
>>>>>>> * start_p2p_device
>>>>>>> * set_mcast_rate
>>>>>>> * testmode
>>>>>>> * channel_switch
>>>>>>> * Unknown command (104)
>>>>>>> * connect
>>>>>>> * disconnect
>>>>>>> Supported TX frame types:
>>>>>>> * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80
>>>>>>> 0x90
>>>>>>> 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
>>>>>>> * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70
>>>>>>> 0x80 0x90
>>>>>>> 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
>>>>>>> * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80
>>>>>>> 0x90 0xa0
>>>>>>> 0xb0 0xc0 0xd0 0xe0 0xf0
>>>>>>> * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70
>>>>>>> 0x80 0x90
>>>>>>> 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
>>>>>>> * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70
>>>>>>> 0x80
>>>>>>> 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
>>>>>>> * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70
>>>>>>> 0x80
>>>>>>> 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
>>>>>>> * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70
>>>>>>> 0x80 0x90
>>>>>>> 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
>>>>>>> * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70
>>>>>>> 0x80
>>>>>>> 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
>>>>>>> Supported RX frame types:
>>>>>>> * IBSS: 0x40 0xb0 0xc0 0xd0
>>>>>>> * managed: 0x40 0xd0
>>>>>>> * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
>>>>>>> * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
>>>>>>> * mesh point: 0xb0 0xc0 0xd0
>>>>>>> * P2P-client: 0x40 0xd0
>>>>>>> * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
>>>>>>> * P2P-device: 0x40 0xd0
>>>>>>> software interface modes (can always be added):
>>>>>>> * AP/VLAN
>>>>>>> * monitor
>>>>>>> valid interface combinations:
>>>>>>> * #{ managed, P2P-client } <= 8, #{ P2P-GO } <= 3, #{
>>>>>>> P2P-device } <= 1, #{ AP } <= 7,
>>>>>>> total <= 8, #channels <= 1, STA/AP BI must match
>>>>>>> HT Capability overrides:
>>>>>>> * MCS: ff ff ff ff ff ff ff ff ff ff
>>>>>>> * maximum A-MSDU length
>>>>>>> * supported channel width
>>>>>>> * short GI for 40 MHz
>>>>>>> * max A-MPDU length exponent
>>>>>>> * min MPDU start spacing
>>>>>>> Device supports TX status socket option.
>>>>>>> Device supports HT-IBSS.
>>>>>>> Device supports SAE with AUTHENTICATE command
>>>>>>> Device supports scan flush.
>>>>>>> Device supports per-vif TX power setting
>>>>>>> Driver supports a userspace MPM
>>>>>>> Driver/device bandwidth changes during BSS lifetime (AP/GO
>>>>>>> mode)
>>>>>>> Device supports static SMPS
>>>>>>> =====================================================
>>>>>>>
>>>>>>> I am grateful for any help here and do have some time to help
>>>>>>> debugging the issue.
>>>>>>>
>>>>>>> Marcel
>>>>>>>
>>>>>>> --
>>>>>>>
>>>>>>> ------------------------------------------------------
>>>>>>> This message is not intended to have
>>>>>>> contractual effect
>>>>>>> ------------------------------------------------------
>>>>>>>
>>>>>>> _______________________________________________
>>>>>>> ath10k mailing list
>>>>>>> ath10k at lists.infradead.org
>>>>>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>>>>> _______________________________________________
>>>>>> ath10k mailing list
>>>>>> ath10k at lists.infradead.org
>>>>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>>>>
>>>>>
>>>>> --
>>>>> Jorge Baranda
>>>>> Research Engineer, MSc
>>>>> jorge.baranda at cttc.es
>>>>>
>>>>> Centre Tecnològic de Telecomunicacions de Catalunya (CTTC)
>>>>> Av. Carl Friedrich Gauss, 7
>>>>> 08860 Castelldefels, Barcelona (Spain)
>>>>> Tel: +34 93 645 29 00 Ext: 2171
>>>>> Fax. +34 93 645 29 01
>>>>> www.cttc.es
>>>>>
>>>>>
>>>>>
>>>>> _______________________________________________
>>>>> ath10k mailing list
>>>>> ath10k at lists.infradead.org
>>>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>>> _______________________________________________
>>>> ath10k mailing list
>>>> ath10k at lists.infradead.org
>>>> http://lists.infradead.org/mailman/listinfo/ath10k
>>>
>>>
>>> --
>>>
>>> ------------------------------------------------------
>>> This message is not intended to have
>>> contractual effect
>>> ------------------------------------------------------
>>
>>
>
--
Jorge Baranda
Research Engineer, MSc
jorge.baranda at cttc.es
Centre Tecnològic de Telecomunicacions de Catalunya (CTTC)
Av. Carl Friedrich Gauss, 7
08860 Castelldefels, Barcelona (Spain)
Tel: +34 93 645 29 00 Ext: 2171
Fax. +34 93 645 29 01
www.cttc.es
More information about the ath10k
mailing list