ath10k: firmware crash in station mode

[Vu Hai NGUYEN]

I tried to set up station mode using ath10k and wpa_supplicant.
If I used the firmware in branch 10.1 version firmware-2.bin_10.1.467.2-1 (which said that support STA mode but not well tested) , it crashed after associating with the access point:

wlan0: SME: Trying to authenticate with 00:15:61:10:51:de (SSID='actia' freq=2457 MHz) 
wlan0: authenticate with 00:15:61:10:51:de                           
wlan0: send auth to 00:15:61:10:51:de (try 1/3)                                 
wlan0: authenticated                                                            
wlan0: Trying to associate with 00:15:61:10:51:de (SSID='actia' freq=2457 MHz)  
wlan0: associate with 00:15:61:10:51:de (try 1/3)                               
wlan0: RX AssocResp from 00:15:61:10:51:de (capab=0x421 status=0 aid=1)         
wlan0: associated                                                               
ath10k: firmware crashed!                                                       
ath10k: hardware name qca988x hw2.0 version 0x4100016c                          
ath10k: firmware version: 10.1.467.2-1                                          
ath10k: target register Dump Location: 0x00401930                               
ath10k: target Register Dump                                                    
ath10k: [00]: 0x4100016C 0x00000000 0x009A123A 0x00000000                       
ath10k: [04]: 0x00000000 0x00000000 0x00000000 0x00000000                       
ath10k: [08]: 0x00000000 0x00000000 0x00000000 0x00000000                       
ath10k: [12]: 0x00000000 0x00000000 0x00000000 0x00000000                       
ath10k: [16]: 0x00000000 0x00000000 0x00000000 0x009A123A                       
ath10k: [20]: 0x00000000 0x00401930 0x00000000 0x00000000                       
ath10k: [24]: 0x00000000 0x00000000 0x00000000 0x00000000                       
ath10k: [28]: 0x00000000 0x00000000 0x00000000 0x00000000                       
ath10k: [32]: 0x00000000 0x00000000 0x00000000 0x00000000                       
ath10k: [36]: 0x00000000 0x00000000 0x00000000 0x00000000                       
ath10k: [40]: 0x00000000 0x00000000 0x00000000 0x00000000                       
ath10k: [44]: 0x00000000 0x00000000 0x00000000 0x00000000                       
ath10k: [48]: 0x00000000 0x00000000 0x00000000 0x00000000                       
ath10k: [52]: 0x00000000 0x00000000 0x00000000 0x00000000                       
ath10k: [56]: 0x00000000 0x00000000 0x00000000 0x00000000                       
br0: received packet on eth0 with own address as source address                 
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready                              
br0: port 2(wlan0) entering forwarding state                                    
br0: port 2(wlan0) entering forwarding state                                    
wlan0: Associated with 00:15:61:10:51:de                                        
ath10k: failed to put down monitor vdev 1: -11                                  
ath10k: failed to to request monitor vdev 1 stop: -11                           
ath10k: failed to synchronise monitor vdev 1: -110                              
ath10k: failed to stop monitor vdev: -110                                       
ath10k: failed to request wmi monitor vdev 1 removal: -11                       
ath10k: failed to delete monitor vdev: -11                                      
ieee80211 phy0: Hardware restart was requested                                  
ath10k: failed to request monitor vdev 2 creation: -108                         
ath10k: failed to create monitor vdev: -108                                     
ath10k: failed to start monitor (promisc): -108                                 
wlan0: CTRL-EVENT-CONNECTED - Connection to 00:15:61:10:51:de completed [id=0 id_str=]                                                                          
ath10k: device has crashed during init                                          
ath10k: failed to wait for target to init: -70                                  
ath10k: failed to power up target using warm reset: -70                         
ath10k: trying cold reset                                                                                                     

Than I tried another version of firmware from branch 999. (which said that support STA mode) but it worse, the firmware crashed before seeing the access point. (can not associate)
This crashed is because of my system or just only the firmware issue? And is the firmware still continue developping? (There is a debug message of my system in the attached file if any one are interested in)

Btw is there anyone could set a channel (from 52 and more) that employs DFS sucessfully confirm it for me cause I can not do it until now :D
Thank you all of you for the support,

NGUYEN Vu Hai
Acita-Sodielec
Route de Mayres - B.P. 9
12100 St GEORGES DE LUZENCON
FRANCE
-------------- next part --------------
An embedded and charset-unspecified text was scrubbed...
Name: debug_mess.txt
URL: <http://lists.infradead.org/pipermail/ath10k/attachments/20140515/790dea3f/attachment-0001.txt>